User manual STANDARD HORIZON CPF390I

[. . . ] CP390i - GPS Chart Plotters CPF390i - GPS Chart Plotters/Fish Finder Owner's Manual WAAS 3D CP390i CPF390i WARNING!!!Electronic charts displayed by the GPS Chart Plotter are believed to be accurate and reliable, but are not intended to be a substitute for the official charts, which should remain your main reference for all matters related to the execution of safe navigation. For this reason you should always keep the official published and approved nautical charts on board. FCC Compliance Statement This device complies with Part 15 of the FCC limits for Class A digital devices. This equipment generates, uses and can radiate radio frequency energy and, if not installed or used in accordance with the instructions may cause harmful interference with radio communications. [. . . ] The available functions are described in the table below. Language Mode : Allows setting the language to display chart information. The language is chosen among the list of languages available on the cartographic data (data cartridge or embedded charts). Selections are: Off : Enables the language chosen in the Language menu above. If the selected language is not present on the objects information, English is used. After the selection is made, press [CLR] repeatedly or move the ShuttlePoint knob to the left repeatedly until the Chart page is shown. NOTE a. When the Chart Language is changed, the following settings are automatically selected: MODE is set to Off and Chart Language is set to your selection. If the C-CARD is removed or changed, the Chart Language should be confirmed and changed if necessary. 6. 0. 9 Pictures or Diagrams Using optional C-MAP BY JEPPESEN MAX data cards allows you to show pictures or diagrams on the CP390i and CPF390i display. These Pictures are typically used to facilitate the identification of cartographic objects or places around the chart: they can be the landscape layout nearby a harbor, the shape of a bridge or of a buoy etc. On some objects, such as bridges, the image associated can represent the Diagram representing the shape of the objects and the various characteristics (length, height, type of bridge etc. ). Figure 6. 0. 9 - Pictures and Diagrams CP390i and CPF390i Page 65 How to show the Pictures or Diagrams of a Object They are shown on the Chart page with the camera icon , see the figure below: WAAS 3D Figure 6. 0. 9a - Example of camera icon Move the cursor over the camera icon. You are get the quick info on the object and there is the camera icon on the top bar of the window: WAAS 3D Figure 6. 0. 9b - Example of Quick Info on camera icon Press [IMAGE] for 1 second to display the image on the screen: Figure 6. 0. 9c - Example of displayed image Otherwise press [EXPAND] to open the Full Info on the object. Note that on the Full Info, there is the small camera icon on a corner of the square containing the object icon. To see the picture press [MENU] when the object with a picture is highlighted. When the picture is shown, it is possible to fit it to screen by pressing [ENT], to change the contrast by pressing [ZOOM IN] or [ZOOM OUT] and to display the next picture associated, if any, by moving the ShuttlePoint knob left or right. Page 66 CP390i and CPF390i 6. 0. 10 Enhanced Port Info Optional C-MAP BY JEPPESEN MAX C-Cards include additional Port Services that were not present before. Additional attributes of Port Areas and Port Marinas have been included as Location, Country, Region, State, Harbour master telephone number etc. , see the following figure. WAAS 3D 1 1 PORT icon Figure 6. 0. 10 - Example of enhanced Port Info CP390i and CPF390i Page 67 Page 68 CP390i and CPF390i 7. CREATING MARKS Definitions: MARK Can be a stand alone position or be linked to a Route. A Mark is place on the Chart Page using [MARK] or by entering in information in the MARK/WAYPONTS menu and selecting NEW MARK. Are placed on the Chart page using [ROUTE]. NOTE The difference between a Mark and a Waypoint is a. When a Route is created using WAYPOINTS and the ROUTE is deleted the WAYPOINTs are also deleted. If a Route is created using MARKS and the ROUTE is deleted the MARKs remain. 7. 0 CREATING A NEW MARK USING THE CHART PAGE 1. You will notice a Mark is placed under the location of the Cursor and a popup window is shown with the exact Lat/Lon of the Mark. If the position is incorrect press [EDIT] that will allow you to change the position, Mark name and icon type. Refer to Par. 7. 1 for details. 1 Mark placed under Cursor 2 Lat/Lon of Mark, DST/BRG from vessel location 4 1 Press Soft Key to show the 3 Marks/Waypoint List, to edit, to move or to delete Mark 2 3 Figure 7. 0 - Mark creation 4 Vessel location NOTE After entering in all the Marks it is a good practice to back up the points to an User C-CARD. Refer to Section 11. 7. 1 EDITING A MARK If a Mark has previously been created and you wish to Edit it, move Cursor over the top of the Mark. [. . . ] 112, 151 Page 164 CP390i and CPF390i RMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13, 32, 69, 77, 78, 79, 81, 82, 115, 151 Route Check . . . . . . . . . . . . . . . . . . . . . . . 13 CP390i and CPF390i Page 165 Temp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 Page 166 CP390i and CPF390i WAAS 2D/3D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]