User manual STANDARD HORIZON HX370S

[. . . ] HX370S VHF/FM Marine Handheld Transceiver Owner's Manual TABLE OF CONTENTS FCC LICENSE INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FCC NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If an incoming signal is detected on one of the channels in the scanning loop, the radio will pause on that channel, allowing you to listen to the incoming transmission. Select the desired channel to be included in the scanning loop using the [ ] or [ ] key. Press the MEM key to store the channel into the transceiver's scanning memory. To delete a channel from the transceiver's scan memory, press the MEM key again while the memorized channel is displayed. All channels programmed remain in the transceiver's scan memory even if the power is turned off. Press the SQL key, then press the [ ] or [ ] key until background noise is eliminated. The scan proceeds from the lowest to the highest programmed channel number and stops on channels when a transmission is received. Scanning will resume when the squelch closes after the incoming signal disappears at the end of the transmission. To stop the scan, press the SCAN, 16/9, or WX key. Page 20 HX370S 5. 8 PROGRAMMABLE PRIORITY SCAN The priority scanning feature allows the radio to scan while also keeping watch on a particularly important "priority channel. " The following channels can be set as the priority channel: 16, 09, and Preset Channels 1 through 8 (Preset Channels are described in section 5. 14). To set the priority channel, hold down the 16/9 key and press the MEM key. The channel will change from 16 to 09 to Preset 1 to Preset 2 to Preset 3 to Preset 4 to Preset 5 to Preset 6 to Preset 7 to Preset 8 with each press of the MEM key. The displayed channel will be set as the priority channel when the 16/9 key is released. Scanning will proceed between the memorized channels and the priority channel. "P" is shown on the left side of the channel number during priority scanning. As an example of priority scanning, let us say that channels 06, 07, and 08 are memorized in the transceiver's scan memory. Priority scanning will proceed in the following sequence: [CH06] [Priority Channel] [CH07] [Priority Channel] [CH08] [Priority Channel] [CH06] [Priority Channel] . . . . . . Even when the transceiver stops and listens to the signal of a programmed channel, the transceiver will "dual watch" between this channel and the priority channel. Therefore, your priority watching of the designated channel is not compromised when the scanner has paused on an active channel. 5. 9 DUAL WATCH The Dual Watch feature allows the radio to watch for a transmission on the priority channel and another selected Marine channel until a signal is received. The priority channel is determined per the discussion in section 5. 8 "PROGRAMMABLE PRIORITY SCAN" as described previously. To start the Dual Watch feature, select a channel to be dual watched with the priority channel and press and hold in the SCAN key. The radio checks the priority channel for voice traffic every one second. A small "DW" icon will be shown blinking on the left of the display during scanning. [. . . ] STANDARD HORIZON will not warrant installation, maintenance or service of the Products. In all instances, STANDARD HORIZON's liability for damages shall not exceed the purchase price of the defective Product. This warranty only extends to Products sold within the 50 States of the United States of America and the District of Columbia. STANDARD HORIZON will pay all labor to repair the product and replacement parts charges incurred in providing the warranty service except where purchaser abuse or other qualifying exceptions exist. [. . . ]