User manual STANTON DJLAB.2

[. . . ] This appliance shall not be exposed to dripping or splashing water and that no object filled with liquids such as vases shall be placed on apparatus. 9. 10. 11. IMPORTANT SAFETY INSTRUCTIONS CAUTION CAUTION: To reduce the risk of electric shock, do not remove the cover (or back). Refer servicing to qualified service personnel. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the use to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION To prevent electric shock, do not use this polarized plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure. LINE VOLTAGE SELECTION 115V The desired voltage of your turntable may be set with the VOLTAGE SELECTOR switch on the rear panel of the main unit, using a screwdriver. 2) Do not twist the VOLTAGE SELECTOR switch with excessive force as this may cause damage. 230V 3) If the VOLTAGE SELECTOR switch does not move smoothly contact a qualified serviceman. [. . . ] 12) Level Indicators ­ The dual LED indicators are used to indicate the master output level of channels Right and Left. 13) Mic EQ ­ The mic channel include a two-band EQ with a range of +10dB to ­10dB. QUICK SETUP DIAGRAM Study this setup diagram. Finally, connect the stereo outputs to the power amplifier(s) and/or audio receivers such as tape decks. IMPORTANT: Always switch on your audio input sources such as turntables or CD players first, then your mixer, and finally any amplifiers. When turning off, always reverse this operation by turning off amplifiers, then your mixer, and then input devices. SPECIFICATIONS M. 201 INPUT / OUTPUT IMPEDANCE & SENSITIVITY: LINE -14dB/10K OHM ±2dB PHONO -50dB /47K OHM ±2dB MIC -60dB /2. 2K OHM ±2dB MASTER 1K OHM PHONES 0dB/33 OHM ±2dB (LOAD=32 OHM) MAX. OUTPUT (THD=1%) MASTER MORE THAN +14dBV MAX PHONES MORE THAN +21dBV MAX CHANNEL BALANCE WITHIN 3dB FREQUENCY RESPONSE: LINE 20-20KHz ±2dB PHONO 20-20KHz +2, -3dB (RIAA) MIC 20-20KHz +2/-3dB OUTPUT NOISE (IEC-A WEIGHTED) LINE LESS THAN -90dBV PHONO LESS THAN -80dBV MIC LESS THAN -50dBV THD + N: LINE PHONO MIC PHONES (MASTER 0dBV OUTPUT, MAXIMUM GAIN, w/ 20kHz LPF) LESS THAN 0. 05% 20 - 20KHz LESS THAN 0. 1% 20 - 20KHz (IEC-A WTD) LESS THAN 0. 2% 20 - 20KHz (IEC-A WTD) LESS THAN 0. 1% 20 - 20KHz (FROM LINE INPUT) LESS THAN -80dB AT 1KHz BETWEEN CHANNELS. (TERMINATED UNUSED INPUTS) CROSSTALK MIC EQ HI LOW ±10 +/- 2dB AT 10KHz ±10 +/- 2dB AT 100Hz CHANNEL EQ HI 9 +/- 2dB AT 13KHz -15 +/- 3dB AT 13KHz MID 9 +/- 2dB AT 1KHz LESS THAN -23dB AT 1KHz LOW 9 +/- 2dB AT 70Hz -26 +/- 3dB AT 70Hz POWER SOURCE AC 9V, 1000mA DIMENSIONS 230 (W) X 267 (D) X 111 (H) mm WEIGHT 1. 61Kgs BEFORE USE *Check that the following parts are included in the package with the main unit: 1) Turntable platter 2) Slip mat 3) 45-rpm adaptor 4) Counterweight 5) 500B cartridge and headshell 6) Operating instructions 7) RCA cables with ground wire 8) Target light 9) AC cord 10) Cloth dust cover *Notes: 1) Do not connect the AC power plug before assembly has been completed. 2) Read this manual carefully before using the unit and be sure to store the manual in a safe place for future reference. T. 60 TURNTABLE CONTENTS T. 60 TURNTABLE CONTENTS 1) 2) 3) 4) 5) 6) 7) 8) 9) Start/Stop Button Strobe Dots Slip Mat Center Spindle Power Switch 33/45 Button Target Light Base Pitch Control Slider Headshell Locking Nut 10) 11) 12) 13) 14) 15) 16) 17) Tonearm Arm Rest Counterweight 45-rpm Adaptor Position For Preparing Cartridge Phono Output GND Power Cord Connector PLACEMENT · Do not place the unit in a location where it will be exposed to direct sunlight or near a heating appliance. · Do not place the unit in a location where there is high humidity or a lot of dust. · Cartridge may pick up slight sound pressures or vibrations from the speakers coming along the floor or through the air resulting in feedback. · The legs have functions for adjusting the height of the unit itself. Adjust the legs to stabilize the main body horizontally. ASSEMBLY 1. Remove the main unit with the packing from the box and take off the packing. Installation of cartridge: When installing a cartridge, refer to the operating instructions of that cartridge. During installation, attach the stylus protector to guard the stylus tip from damage. White (L+) Left channel+ Blue (L-) Left channelRed (R+) Right channel+ Green (R-) Right channel(2) Install the cartridge to the headshell and tighten it with screws provided with the cartridge. Insert the headshell into the front end of the tonearm, then turn the lock nut clockwise with the headshell firmly held horizontally. Twist it lightly and it will screw onto the rear shaft of the tonearm. Adjustment of horizontal zero (0) balance and stylus pressure: (a) Remove the stylus protector, do not touch the stylus tip during the adjustment. (b) Release the arm clamp and lift the tonearm from the arm rest to free it. (c) Rotate the counterweight until the tonearm is approximately balanced horizontally (floats freely). (e) Hold the counterweight stationary with one hand and rotate only the stylus-pressure ring to bring the number "0" of the ring into alignment with the center line on the tonearm rear shaft. [. . . ] Stanton assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the merchandise. Stanton's liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party, or product liability, and relating to the merchandise shall not exceed the price received by Stanton from your purchase of such merchandise. In no event will Stanton be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Stanton or otherwise. To the extent permitted by law and except as otherwise provided above, Stanton disclaims any express or implied warranties of merchantability or fitness for a particular purpose. [. . . ]