User manual STANTON M.201

[. . . ] If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. [. . . ] Listen here before bringing up channel faders or moving the crossfader. Level Indicators ­ The dual LEDs indicators are used to indicate the master output level of channels Right and Left. Mic EQ ­ The mic channel include a two-band EQ with a range of +10dB to ­10dB. MIXER CONTENTS 14. Always use this connection when using standard turntables with ground cable. (Some turntables like the T. 80 / T. 120 do not require grounding wire). When these connectors are used, your signal is fed directly to the high-quality RIAA phono pre-amplifiers. Line level sources will overload the sensitive phono pre-amps and will cause distortion. Line Inputs - Unbalanced RCA jacks for connecting stereo audio from line level sources such as CD players, HiFi VCRs, cassette decks, DAT machines, laser discs, tuners, even synthesizers or other mixing consoles. NOTE: Plug mono audio sources into both Left and Right inputs using a "Y" cable connector. Master Output - Unbalanced RCA connectors controlled by the Master level. Note*** Remember to turn ALL volume levels down when turning on/off the unit. Power Connector - Plug in the included power supply here. QUICK SETUP DIAGRAM Study this setup diagram. Finally, connect the stereo outputs to the power amplifier(s) and/or audio receivers such as tape decks. IMPORTANT: Always switch on your audio input sources such as turntables or CD players first, then your mixer, and finally any amplifiers. When turning off, always reverse this operation by turning off amplifiers, then your mixer, and then input devices. SPECIFICATIONS INPUT / OUTPUT IMPEDANCE & SENSITIVITY: LINE -14dB/10K OHM ±2dB PHONO -50dB /47K OHM ±2dB MIC -60dB /2. 2K OHM ±2dB MASTER 1K OHM PHONES 0dB/33 OHM ±2dB (LOAD=32 OHM) MAX. OUTPUT (THD=1%) MASTER MORE THAN +14dBV PHONES MORE THAN +21dBV CHANNEL BALANCE WITHIN 3dB FREQUENCY RESPONSE: LINE 20-20KHz ±2dB PHONO 20-20KHz +2, -3dB (RIAA) MIC 20-20KHz +2/-3dB OUTPUT NOISE (IEC-A WEIGHTED) LINE LESS THAN -90dBV PHONO LESS THAN -80dBV MIC LESS THAN -50dBV THD + N: LINE PHONO MIC PHONES (MASTER 0dBV OUTPUT, MAXIMUM GAIN, w/ 20kHz LPF) LESS THAN 0. 05% 20 - 20KHz LESS THAN 0. 1% 20 - 20KHz (IEC-A WTD) LESS THAN 0. 2% 20 - 20KHz (IEC-A WTD) LESS THAN 0. 1% 20 - 20KHz (FROM LINE INPUT) LESS THAN -80dB AT 1KHz BETWEEN CHANNELS. (TERMINATED UNUSED INPUTS) CROSSTALK MIC EQ HI LOW ±10 +/- 2dB AT 10KHz ±10 +/- 2dB AT 100Hz CHANNEL EQ HI 9 +/- 2dB AT 13KHz -15 +/- 3dB AT 13KHz MID 9 +/- 2dB AT 1KHz LESS THAN -23dB AT 1KHz LOW 9 +/- 2dB AT 70Hz -26 +/- 3dB AT 70Hz POWER SOURCE AC 9V, 1000mA DIMENSIONS WEIGHT 230 (W) X 267 (D) X 111 (H) mm 1. 61Kgs Stanton Magnetics, Inc. ­ Warranty Provision ­ Returns for Repairs or Replacement WARRANTY Through Stanton's authorized dealers around the World, Stanton, or one of Stanton's authorized distributors outside the U. S. , will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) year following the date of original purchase. [. . . ] To the extent permitted by law and except as otherwise provided above, Stanton disclaims any express or implied warranties of merchantability or fitness for a particular purpose. You may also have additional rights, which are subject to variation from state to state and country to country. If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above, please include a written explanation with the merchandise when returned pursuant to the terms and conditions set forth herein. Please register your product online at www. stantondj. com or mail your completed warranty card to: Stanton Magnetics, Inc, 3000 SW 42 St. [. . . ]