User manual STANTON SK-6

[. . . ] Remove the fader to be cleaned by unscrewing the 2 outer screws (removing the 2 inner screws will detach the fader from the fader plate) and disconnect the cable coming from the mixer. Spray a small amount of cleaner or lubricant into both ends of the fader and slide the fader back and forth a few times to spread the fluid evenly throughout the fader. Shake and wipe off excess fluid before re-assembling the fader. SK SIX Professional performance mixer R E P L AC E M E N T PA RT S To replace the cross or channel faders, follow steps 1 and 2 of the cleaning instructions. The following replacement parts are available from Stanton or your local Stanton dealer. PL-SK6 3PL-SK6 LF-SK6 CF-SK6 Two way input toggle switch Three way input toggle switch with FLASHTM Channel input fader Crossfader PP-SK6 PS-18US PS-18EU PS-18UK PROTEKTTM panel US Power Supply (110v) European Power Supply (220v) UK only Power Supply (240v) ROTATING AND REPLACING THE INPUT TOGGLE SWITCHES ROTATING INST RU C TI O NS 1 . [. . . ] No power. Amplifier or outboard gear connected to the record output. Improperly connected AC cord or power line source not on. · Follow all security advice printed on your mixer · When removing the unit's AC plug from the power source, grasp and pull the plug, NEVER the cord itself!· Avoid placing your mixer near heat sources, such as power amplifiers. · When in use, place your mixer on a stable surface, away from vibration. Impact, or heavy vibration may compromise the unit's mechanical integrity. The manufacturer is not responsible for damage resulting from an impact, or misuse. · When in use, place your mixer away from sources of hum or noise, such as transformers, or electric motors. · To prevent overheating, always provide your mixer with adequate ventilation air space. · To avoid damage due to AC voltage peaks, always disconnect your mixer from the power source during electrical storms. The manufacturer is not responsible for any damage or personal injury resulting from unauthorized user-servicing or modifications. In addition, the warranty will be void if any unauthorized service by the user is detected. Always return you mixer to an authorized Stanton dealer for servicing. The amplifier is turned up, but there is no signal. Faulty output connections Improper level adjustment. No signal in headphones. Improper connection. Improper level or cue mix settings. D E S C R I P T I O N O F FU N C TI O N S 1. this is used to set the level of the signal going to the outbpard effects processor or stomp box. This is used to control the level of the processed signal going back into themixer 4. EQ: Individual controls for low and high frequency equalization with (+9/-26 dB) Any changes made to EQ settings will change the overall output level. It is recommended headphones with an impedance rating of 200 ohms or less be used for maximum volume. Cue pan: Fades the headphone output between channels 1 and 2, effectively allowing the user to preview a mix. Input Fader Reverse: Reverses the direction of each respective input channel fader. Headphone mute: Mutes the headphones without having to change its level. Input Level Meter: Monitors each channel's input level with peak hold function 16. [. . . ] Therefore, it is warranted to be free from defects in materials (limited as specified below), and workmanship for a period of twelve (12) months from the original purchase date. During this period, all service and parts necessary to repair a defect will be free of charge. This limited warranty applies to mechanical parts which are subject to wear and tear as specified: · Faders, specified durability: 15, 000 cycles · Rotary potentiometers, specified durability: 10, 000 cycles · Switches, specified durability: 10, 000 cycles Consequently, the parts listed above are warranted to be free from defects in materials and workmanship for a period of thirty days (30) days from the original purchase date. FOR THE WARRANTY TO BE VALID, PLEASE COMPLETE THE ONLINE WARRANTY REGISTRATION FORM FOUND AT WWW. STA N TO N M AG N E TI CS . [. . . ]