User manual SYMBOL P470

[. . . ] P470/P370 RF Scanner Product Reference Guide P470/P370 RF Scanner Product Reference Guide 72-38495-03 Revision C December 2003 © 2001-2003 by Symbol Technologies, Inc. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Symbol. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. All software, including firmware, furnished to the user is on a licensed basis. [. . . ] (1. 5 m) Drops to concrete over entire temperature range 4-5 P470/370 RF Scanner Product Reference Guide Table 4-2. Technical Specifications (Continued) Item Dimensions Height Width Depth Laser Classifications 7. 0 in. (9. 8 cm) CDRH Class II, IEC Class 1, IEC Class 2 Description 4-6 Maintenance And Specifications Cradle Pin-outs The following table shows the pin-outs for COM1 on the cradle. Table 4-3. Pin-outs Pin 1 2 3 4 5 6 7 8 9 10 Cradle Reserved VCC (Out) Ground Synapse Data Synapse Clock RXD IN TXD OUT DTR (Tied HI) CTS - IN RTS - OUT Pin 1 4-7 P470/370 RF Scanner Product Reference Guide Beeper Indications / Default Application Error Codes Table 4-4 list beep sequence and their meanings for standard beeps programmed into the scanner. Other applications written for the scanner can have their own beep sequences and therefore are not listed in this table. For additional information on Error Codes, see Communication Errors on page 3-5. Beeper Indications Beeper Sequence Indication Default Application Error Codes Standard Use Short high tone A bar code symbol was decoded (if decode beeper is enabled). N/A 4 Beeps - long low Error code 003 Error code 009 Error code 018 Error code 247 Error code 249 Error code 253 Error code 002 Error code 008 Error code 005 Low Battery 5 Beeps - low tone Convert or format error. Hi/Hi/Hi/Lo tone 4 Beeps - short Hi RS-232 receive error. Battery requires recharging. 4 Beeps - Lo/Hi/Lo/Hi An RF transmission error has occurred. Error code 015 Error code 016 Move closer to the cradle and re-scan Error code 017 the bar code. Error code 024 Parameter Menu Scanning Short high tone Correct entry scanned or correct menu sequence performed. Beeper Indications (Continued) Beeper Sequence Indication Default Application Error Codes N/A Long Lo/Long Hi tone Input error, incorrect bar code or "Cancel" scanned, wrong entry, incorrect bar code programming sequence; remain in program mode. Correct entry scanned or correct menu sequence performed in the scanner but communication error with cradle has occurred. N/A Hi/Lo/Hi/Lo tone N/A 4 Beeps - Lo/Hi/Lo/Hi followed by 2 Beeps - Lo/Hi N/A 4-9 P470/370 RF Scanner Product Reference Guide 4-10 Chapter 5 Parameter Menus Introduction This chapter has the optional parameter bar codes necessary to program the RF scanner. Operational Parameters The RF scanner is shipped with the settings shown in Table 5-1. These default values are stored in non-volatile memory and are preserved even when the scanner is powered down. You can change these default values by scanning the appropriate bar codes included in this manual. The default parameter values can be recalled by scanning the bar code in the section Set Default Parameter on page 5-7. The scanner automatically detects which cable it is attached to, either an RS-232 or a Synapse cable. If it is attached to an RS-232 cable and has either an ICL, Nixdorf, or Fujitsu host interface, then scan the appropriate bar code from page 5-10 after power up. If it is attached to a Synapse cable, plug everything together as described on page 2-3 and then follow the directions that come with the Synapse cable for setting up the host interface. 5-1 P470/370 RF Scanner Product Reference Guide The following table lists the defaults for all parameters. Default Table Parameter Set Default Parameter Communication Protocol Scan & Transmit Application RS-232 Host Type Host Response Timeout RF Channel RF Retries Sleep Time Decimal Separator Key Click Beeper Options Beeper Tone Beeper Volume Power Detect Beep Beep After Good Decode Laser On Time Decode Options Transmit "No Read" Message Linear Code Type Security Levels Bi-directional Redundancy Autodiscriminate Response Time Disabled 1 Disabled 1. 0 second 5-23 5-24 5-26 5-27 High Frequency High Enabled Enabled 3. 0 seconds 5-18 5-19 5-20 5-21 5-22 RS232/Synapse Standard 5 seconds No Default Setting 4 10 seconds Decimal Point (. ) Enabled 5-8 5-9 5-12 5-13 5-13 5-15 5-16 5-17 Default All Defaults Page Number 5-7 5-2 Parameter Menus Table 5-1. Default Table (Continued) Parameter UPC/EAN UPC-A UPC-E UPC-E1 EAN-8 EAN-13 Bookland EAN Decode UPC/EAN Supplementals Decode UPC/EAN Supplemental Redundancy Transmit UPC-A Check Digit Transmit UPC-E Check Digit Transmit UPC-E1 Check Digit UPC-A Preamble UPC-E Preamble UPC-E1 Preamble Convert UPC-E to A Convert UPC-E1 to A EAN-8 Zero Extend Convert EAN-8 to EAN-13 Type UPC/EAN Security Levels UPC/EAN Coupon Code Enabled Enabled Disabled Enabled Enabled Disabled Ignore 7 5-28 5-28 5-28 5-29 5-29 5-30 5-31 5-32 Default Page Number Enabled Enabled Enabled System Character System Character System Character Disabled Disabled Disabled Type is EAN-13 0 Disabled 5-33 5-33 5-33 5-34 5-35 5-36 5-37 5-38 5-39 5-40 5-41 5-43 5-3 P470/370 RF Scanner Product Reference Guide Table 5-1. Default Table (Continued) Parameter Code 128 Code 128 UCC/EAN-128 ISBT-128 Code 39 Code 39 Trioptic Code 39 Set Length(s) for Code 39 Code 39 Check Digit Verification Transmit Code 39 Check Digit Code 39 Full ASCII Conversion Convert Code 39 to Code 32 Code 32 Prefix Code 93 Code 93 Set Length(s) for Code 93 Interleaved 2 of 5 Interleaved 2 of 5 Set Length(s) for I 2 of 5 I 2 of 5 Check Digit Verification Transmit I 2 of 5 Check Digit Enabled 14 Disabled Disabled 5-60 5-61 5-63 5-64 Disabled 4-55 5-57 5-58 Enabled Disabled 2 to 55 Disabled Disabled Disabled Disabled Disabled 5-48 5-49 5-51 5-52 5-53 5-54 5-55 5-56 Enabled Enabled Enabled 5-44 5-45 5-47 Default Page Number 5-4 Parameter Menus Table 5-1. [. . . ] The base to which the scanner is paired has been paired with another scanner. Reconnect to the host using an RS-232 cable and then cycle power (power off then on) to the base. Previous RF transmission not yet complete. 020 021 024 247 249 253 RF Communication Error Memory Allocation Error For repeated occurrence contact Customer Service. RF Communication Error MCL-Link Error MCL-Link Error MCL-Link Error The base is not responding. [. . . ]