User manual TANDBERG DLT-V4

[. . . ] PRODUCT MANUAL TAPE DRIVE DLT-V4 DLT-V4 Product Manual, 81-81523-01 A01, November 2005, Made in USA. Tandberg Data provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Tandberg Data may revise this publication from time to time without notice. Making copies or adaptations without prior written authorization of Tandberg Data is prohibited by law and constitutes a punishable violation of the law. [. . . ] Contact the server or workstation manufacturer for information. 2 Replace the cover on the server or workstation. 3 Connect the power cord to the server or workstation and any peripheral devices that you detached earlier. start. 4 Power on the server or workstation and allow its operating system to 5 Check the tape drive to make sure it is working properly. See Power- On Self-Test (POST) Indicator Activity on page 47 to learn about the tape drive's self-test and initialization features. DLT-V4 Product Manual 24 Chapter 2 Installing the Tape Drive Installing the Internal SATA Tape Drive Installing the Internal SATA Tape Drive This section contains step-by-step instructions for installing the DLT-V4 internal SATA tape drive. 2 Identifying the Steps 2 Installing the tape drive is fast and easy when you follow the instructions in this section in the order presented. Complete the following steps, covered in the next few sections: Table 4 Installing the DLT-V4 Internal SATA Tape Drive -- Overview Step 1 2 3 Instruction Unpack and check the tape drive for shipping damage. Shut down and power off the server or workstation that is to host the tape drive. Power off all peripheral devices attached to the server or workstation. Remove the cover from the server or workstation, as explained in the server or workstation's documentation Install a SATA host adapter in the server or workstation, if necessary. Secure the tape drive in the selected server or workstation. Refer to page 26 page 26 4 5 6 7 8 9 page 27 page 29 DLT-V4 Product Manual 25 Chapter 2 Installing the Tape Drive Installing the Internal SATA Tape Drive Step 12 Instruction Install the server or workstation's cover, connect power cables to all peripheral devices, and apply power to the server or workstation and all peripheral devices. Check the tape drive to make sure it is working properly. Refer to page 31 13 Unpacking the Internal SATA Tape Drive 2 Before you do anything else, unpack and inspect the tape drive for shipping damage. If you notice any damage, report it both to the sales representative and to the shipping company immediately. Note: Save the packing materials in case you need to move or ship the tape drive in the future. You must ship the tape drive in the original (or equivalent) packing materials or you will invalidate the warranty. If there is no damage to the tape drive, select a server or workstation to host the tape drive, then move on to the following installation steps. Installing the Internal SATA Tape Drive 2 In the final installation stage, you install the tape drive in the server or workstation and connect the data and power cables. To install the tape drive, follow these steps: 1 Shut down the operating system and power off the server or workstation. devices. 2 Power off all peripheral devices, such as printers and other connected Caution: Do not go to step 3 until you have completed steps 1 and 2. Failure to follow these instructions may result in damage to the tape drive or other devices. 3 Remove the cover from the server or workstation as described in the server or workstation's documentation. DLT-V4 Product Manual 26 Chapter 2 Installing the Tape Drive Installing the Internal SATA Tape Drive Figure 13 Removing the Workstation Cover (example) 4 Locate an available 5¼-inch drive bay and remove the front cover from the drive bay as described in the server or workstation's documentation. 5 Slide the tape drive into the open drive bay. DLT-V4 Product Manual 27 Chapter 2 Installing the Tape Drive Installing the Internal SATA Tape Drive Figure 14 Installing the Internal SATA Tape Drive Tower 2U enclosure DLT-V4 Product Manual 28 Chapter 2 Installing the Tape Drive Installing the Internal SATA Tape Drive Connecting the Internal SATA Tape Drive to the Server 2 Figure 15 Rear Panel Connections for the SATA Internal Tape Drive The internal SATA tape drive attaches to the server through a SATA interface card. SATA power connector SATA data connector Drive power connector Caution: Connect only one power cable to the drive; connecting both the SATA power cable and the drive power cable to the tape drive may damage the tape drive. 1 Connect one end of the SATA data cable to the tape drive and the other end of the SATA data cable to the SATA host bus adapter. drive. 2 Connect either the SATA power cable or drive power cable to the tape DLT-V4 Product Manual 29 Chapter 2 Installing the Tape Drive Installing the Internal SATA Tape Drive Figure 16 Internal SATA Tape Drive Power and Data Cable Connection Locations SATA data cable SATA power cable or Drive power cable Completing the Internal SATA Tape Drive Installation 2 1 Secure the internal SATA tape drive with the supplied mounting screws in the installation bay, either on the sides or bottom of the tape drive sled, as appropriate for the server or workstation chassis. See figure 17 for an example of where you might find these screws. DLT-V4 Product Manual 30 Chapter 2 Installing the Tape Drive Installing the Internal SATA Tape Drive Figure 17 Securing the Internal SATA Tape Drive in the Installation Bay Note: Some servers and workstations require mounting rails for internal devices. Contact the server or workstation manufacturer for information. 2 Replace the cover on the server or workstation. 3 Connect the power cord to the server or workstation and any peripheral devices that you detached earlier. start. 4 Power on the server or workstation and allow its operating system to 5 Check the tape drive to make sure it is working properly. See Power- On Self-Test (POST) Indicator Activity on page 47 to learn about the tape drive's self-test and initialization features. DLT-V4 Product Manual 31 Chapter 2 Installing the Tape Drive Installing the Device Drivers Installing the Device Drivers This section describes how to install device drivers for Microsoft Microsoft Windows 2000, Windows XP, and Windows 2003 Server. Note: 2 If you intend to use native operating system backup applications, you can find the required device drivers at www. tandberg. com. Commercial backup applications generally provide all necessary device driver support. Microsoft Windows XP and Windows Server 2003 2 1 Make sure that you are logged on to the server or workstation with Administrator privileges. 2 Download and extract the required driver files from www. tandberg. com. [. . . ] Also see Advanced PRML. PWA Printed Wiring Assembly. R Restore To replace data on the hard drive with data obtained from another media device. RoHS Restrictions on Hazardous Substances is an EU directive that restricts, and in some cases bans, the use of certain compounds in the manufacture of electronic equipment. RoHS mandates that new electrical and electronic equipment put on the market does not contain lead, mercury, cadmium, hexavalent chromium, poly-brominated biphenyls (PBB), or poly-brominated diphenyl ethers (PBDE). S SAN Storage Area Network. A Serial ATA International Organization (SATA-IO) standard for the interface between a computer and peripheral controllers. [. . . ]