User manual TANDBERG LTO3

[. . . ] 2U Autoloader 6. 4® LTO3 User Reference Manual Document No: DOCSP 301283 Date: Aug. , 2005 AUTOLOADER LTO3 ­ User Reference Manual Rev. 1. 01 TANDBERG DATA Page 1 of 79 Warnings Precautions Product Overview product name LTO3 AUTOLOADER 6. 4 P/N 8330 7071 00 description 1 drive & 8 slots, 2U, Accessories product name SCSI cable Terminator Power cord Manual CD & Quick Reference Guide BCR (customer installable) BCR Installation Guide LTO 3 only LTO 3 only (1x EU version, 1x US version) description Options product name Remote Management Card RackMount Kit P/N 433023 433026 description Web Administ ration Tool AUTOLOADER LTO3 ­ User Reference Manual Rev. 1. 01 TANDBERG DATA Page 2 of 79 Warnings Precautions SERVICE & SUPPORT INFORMATION: Europe TANDBERG Data GmbH Feldstr. 81 D-44141 Dortmund Germany Phone: 0049 ­ (0)231 ­ 5436 142 Fax: 0049 ­ (0)231 ­ 5436 143 USA INOSTOR Inc. [. . . ] STATUS) CHANGE LDR MODE AUTOMATIC (-) (+) See Note 2 & 3 (-) (+) CLEAN DRIVE (INV. CANCEL, from any LCD display in row, will return to Curent Status, Home Screen. CANCEL, from all lower LCD displays, will return to the Respective LCD display, detailed in the top ROW. ENTER, from all lower LCD displays will invoke operation depicted on LCD. (-) (+) (-) (+) BARCODE READER OFF (-) (+) PROTECTION MODE OFF (-) (+) (+) SERIAL NUMBER 0123456789 Figure 20 Interaction Mode, overview AUTOLOADER LTO3 ­ User Reference Manual Rev. 1. 01 TANDBERG DATA Page 3 5 of 79 Operation and Maintenance Configuration 8. 5 Configuration For most installations, the default configuration of the autoloader does not need to be changed. For further information see ThinStor ®Plus LTO3 Autoloader ­ Operator's Manual. However, if necessary, you can use the operator panel to make the following changes to the autoloader configuration: You can change the SCSI IDs for the autoloader and the tape drive using the 'Configuration'. ! IMPORTANT The autoloader and the tape drive must each have unique SCSI IDs. It is your responsibility to make sure you do not assign duplicate IDs within a bus. 8. 6 Operation After you install and configure the autoloader and install your application software on the host computer, the autoloader performs most operations automatically. Operator intervention includes the following activities: n n Monitoring autoloader operation and status Performing autoloader and tape drive operations 8. 6. 1 Monitoring Autoloader Operation and Status During normal operation, the 'Status screen' is displayed on the LCD. By default, the 'Status screen displays the current operating status of the autoloader and tape drive. ' To set the operator panel to user interaction mode, press a key. This mode allows you to use the [Enter] or [Cancel] and [+] or [­] buttons to display options for issuing commands to the autoloader, viewing information screens, and configuring the autoloader. 8. 7 Performing Autoloader and Tape Drive The 'Commands' screen provides options for importing and exporting cartridges, loading and unloading a cartridge from the tape drive, cleaning the tape drive, and updating the cartridge inventory. 8. 7. 1 Importing and Exporting Cartridges The Import command under the Library Commands menu allows you to place a cartridge into a specific cartridge slot through the cartridge access port. When you issue an Import command, the cartridge carousel moves the specified cartridge slot into position in front of the cartridge access port and slides the door open. The cartridge loader then grasps the cartridge, pulls it into the autoloader, and closes the door. The 'Export' command allows you to remove a cartridge from a specific cartridge slot through the cartridge access port. When you issue an 'Export' command, the cartridge carousel moves the specified cartridge slot into position in front of the cartridge access port and slides the door open. The cartridge loader then pushes the cartridge far enough out through the door to allow you to remove it. AUTOLOADER LTO3 ­ User Reference Manual Rev. 1. 01 TANDBERG DATA Page 3 6 of 79 Operation and Maintenance Performing Autoloader and Tape Drive 8. 7. 2 Bulk Exchange The menu item Bulk Exchange was designed to make the autoloader more user friendly. This item enables a user to import or export a specific amount of cartridges e. g. this item makes sense if a user wants to exchange a complete set of cartridges. It's up to the user to import a new cartridge or to move to the next slot #2. The same procedure then takes place for slot #2 to slot #8. 8. 7. 3 Load and unload a Cartridge The load cartridge command under the 'Commands' menu allows you to load the cartridge in the specified slot into the tape drive. When you issue a 'Load cartridge' command, the cartridge carousel moves the specified cartridge slot into position in front of the tape drive. [. . . ] 73 73 64 64 64 73 17 32 73 69 13 AUTOLOADER LTO3 ­ User Reference Manual Rev. 1. 01 TANDBERG DATA Page 7 7 of 79 Index Error Code descript ion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Log example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Media related . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Messages and codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Exporting cartridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 External fan Analysis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 F FCC Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Field immunity Magnetic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Radio frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Front mount brackets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Front panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Menu structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Messages SCSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]