User manual TANDBERG MXP F8 ADMINISTRATOR GUIDE

[. . . ] Software version F8 AUGUST 2010 TANDBERG MXP Administrator Guide www. tandberg. com D14033. 06--AUGUST 2010 1 MXP Contents Contents Introduction Getting started The menu structure The settings library Using the system Physical interfaces Peripheral equipment Administrator Guide Appendices Contact us What's in this guide? Chapter 0 Table of Contents - Hidden text anchor Table of contents Introduction What's new in version F8?8 New products added to the guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Intellectual Property Rights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Trademark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] * TANDBERG 550 MXP has Audio 2 and Headset Mic D14033. 06--AUGUST 2010 191 MXP Contents Introduction Getting started The menu structure The settings library The settings library Using the system Physical interfaces Peripheral equipment Administrator Guide Appendices Contact us MENU ADDRESS Control Panel > Audio > AUDIO OUTPUTS SETTINGS DESCRIPTION AUDIO OUT 1-3 Applies to: 8000 MXP, 6000 MXP Profile, Maestro MXP OUT1: is intended for connection to TANDBERG Digital Natural Audio Module, televisions or audio amplifiers. OUT2 (AUX): is intended for connection to audio recording equipment or to a telephone add-on hybrid. The signal is a mix of audio from both the far end and local end (not from Audio in 5). Do not connect Out2 (AUX) to a loudspeaker placed in the same room as the microphones connected to the system. This will cause "howling" and possible damage to the speaker system. OUT3 (VCR): is intended for connection to a VCR or other recording equipment. The signal is a mix of audio from far end and local end (not from Audio in 6). Do not connect Out3 (VCR) to a loudspeaker placed in the same room as the microphones connected to the system. This will cause "howling" and possible damage to the speaker system. INFORMATION NOTE!The Audio Out 2 or Audio Out 3 should never be connected to a loudspeaker placed in the same room as the microphones connected to the system. This will cause "howling" and possible damage to the speaker system. See Interfaces in the Peripheral Equipment section for more information on this topic for your product. When no audio module is detected, audio outputs can be: PRODUCT 8000 6000 Maestro · · Out 2 for VCR Left Out 3 for VCR Right. Control Panel > Audio > AUDIO OUTPUTS AUDIO OUT 1-2* Applies to: 3000 MXP Profile, Tactical MXP, 990/880/770 MXP, 550 MXP, Edge 95/85/75 MXP OUT1: is intended for connection to televisions or audio amplifiers. OUT2 (AUX): is intended for connection to a VCR or other recording equipment. The signal is a mix of audio from far end and local end (except VCR in). NOTE!The Audio Out 2 should never be connected to a loudspeaker placed in the same room as the microphones connected to the system. This will cause "howling" and possible damage to the speaker system. When no audio module is detected, audio outputs can be: 3000 Tactical 990/880/ 770 550 95/85/75 · · Out 1 for VCR Left Out 2 for VCR Right. * TANDBERG 550 MXP has one Audio Output (see Out1) D14033. 06--AUGUST 2010 192 MXP Contents Introduction Getting started The menu structure The settings library The settings library Using the system Physical interfaces Peripheral equipment Administrator Guide Appendices Contact us MENU ADDRESS Control Panel > Audio > AUDIO OUTPUTS SETTINGS DESCRIPTION OUT 1 MODE Set the mode for the Audio Out 1. ANALOG: Setting the Out 1 Mode to Analog will override the auto-detected mode. SPDIF (DIGITAL): Setting the Out 1 Mode to SPDIF (Digital) will override the auto-detected mode. AUTO: If Out 1 Mode is set to Auto, the system will select ANALOG or SPDIF (Digital) mode dependent on the detected Audio Module. If a TANDBERG Digital NAM is detected the SPDIF mode will be selected, otherwise analog mode will be selected. [. . . ] STREAMING ALLOW REMOTE START: Streaming can be started from the Video communication system using the remote control, by using the Data port, or from external user interfaces like the Web-browser or Telnet session. STREAMING ANNOUNCEMENTS: The system will announce to the network that it is streaming. STREAMING PASSWORD: Prevents unauthorized access to the streaming functionality. STREAMING SOURCE: Select between local video and/or far end video to be streamed. [. . . ]