User manual TANDBERG SUPERLOADER DLT QUICK START GUIDE

[. . . ] In a coordinated motion with the other unpacker, lift the autoloader out of the box and place it on a flat, stable surface. e While one unpacker steadies one side of the autoloader, the other unpacker should grip the front of the autoloader with one hand and remove the foam packaging from the other side of the unit. f While one unpacker steadies the autoloader, the other unpacker should remove the foam packaging from the other side of the unit and set down the unit. g Remove the foam inserts from the front of the unit. Tandberg Data recommends that two people unpack the autoloader and that you practice good ergonomic techniques to lessen the risk of personal injury and damage to the unit. [. . . ] (Procedure continues. ) Support bracket Autoloader bracket Support bracket Rear rail in rack Outer cover of rack 10 11 Rackmount the autoloader, continued 2. Slide the autoloader in place so that the front ears of the autoloader align with the front clip nuts. Then loosely install the four screws that connect the two support brackets to the two front rails. e Loosely install the four screws that connect the support brackets (two screws per support bracket) to the autoloader brackets. Autoloader bracket Front rail f Verify that the autoloader is level. g Tighten the four screws that attach the two front ears to the front rails. Support bracket h Tighten the four screws that connect the two support brackets to the two autoloader brackets. i Tighten the four screws that connect the two support brackets to the two rear rails. 13 Front ear 12 5 Sections 5-9 explain how to set up the autoloader. Make the SCSI connection When installing cables, be careful not to damage the SCSI pins on the connectors. Caution a If the host computer is connected to a network, check with the system administrator before turning off power. b Properly power off all peripheral devices connected to the host computer. d Install the supplied 68-pin SCSI cable to the double-stacked SCSI connector that is on the back of the autoloader/DCA and tighten the screws. Make sure that you install it with the correct orientation so that you can fit a terminator or another cable in the other port. 14 Double-stacked SCSI connector e If the autoloader will be the last device on the SCSI bus, install the supplied SCSI terminator to the remaining port that is on the autoloader/DCA and then tighten the screws. f Attach the other end of the SCSI cable to the SCSI host adapter card. g Power back on any peripheral devices that you powered off in Step b. Note: Do not power on the host computer at this time. You must configure the autoloader for SCSI and Ethernet prior to powering on the host. 15 6 Connect the power cord Note: The first time you power on the autoloader, do not power on the host. 7 Power on the autoloader When you first power on the autoloader, it automatically runs a Power On Self Test (POST). After the POST, the left (green) and right (amber) LED flash alternately. · The autoloader performs a calibration and magazine element status. A + appears in the upper right corner of the LCD while calibration is in progress. When the power-on sequence completes and the autoloader is ready, the LCD displays a list of the autoloader options that are present and the Ready LED is steady green. Note: If there is a warning message indicating a change, you may need to press Escape to clear the message. Note: After the first time you power on the autoloader, you should use the switch on the front to power on and off the autoloader. a Push the power switch on the back of the autoloader to the on position (the 1 is pressed). a Make sure that the power switch on the back of the autoloader is off (the 0 is pressed). b Connect the female end of the power cord to the power connector on the back of the autoloader. [. . . ] Caution To prevent damage to the autoloader or the magazine, use both hands when removing the magazine from the autoloader, supporting the entire length of the magazine. d Grasp the magazine by the handle with one hand and slide it out, supporting it underneath with the other hand. Note: When you eject a magazine, you must fully remove it or fully re-install it before powering off the autoloader. Eject a magazine When you want to remove several cartridges at once, eject the magazine(s) first. b Scroll to Eject and press Enter. 20 21 Use magazines and magazine blanks, continued Install a magazine For detailed instructions, see the User Manual. [. . . ]