User manual TEAC TAPE 1.4GB

[. . . ] Precautions during placement: When installing the tape drive unit in the host computer horizontally, the LED on the front panel will be on the left side. When installing the tape drive unit vertically the LED on the front panel can be either above or below the opening for the tape cartridge. Avoid placing the unit (or host computer) in direct sunlight or near heating apparatus; place the unit in a clean moisture-free environment. [. . . ] Do NOT apply solvents such as thinner, benzene, or alcohol to the unit, as these may blemish the surface of the drive. If the tape drive unit does not operate normally even after being connected properly, contact the representative from whom you purchased the unit or our Technical Support number. If problems arise, and you need to take or send the unit to your place of purchase, please reuse the original packing materials. Do NOT vibrate or apply any shocks to the drive (or the host computer). KIT DESCRIPTION Your tape drive Kit comes complete with: (1) Tape drive unit (2) Tape Hardware Installation Guide (3) Arcada Backup Software User Guide (4) Registration card (5) Arcada Backup software program disks for DOS, Windows 3. x and Windows 95 (6) Tape drive interface data cable (7) Mounting screws (8) Mounting brackets for mounting in a 5 l/4" bay + Note: If all items are not contained in your Kit, please return it to the dealer you purchased it from. CONTROLS, CONNECTIONS AND FUNCTIONS Tape800/1600 ON/BUSY LED indicator Tape cartridge insertion window Front View TOOLS YOU MAY NEED Depending on the design of your computer, you may need the following tools to complete the installation. 0 A flat blade screwdriver 0 A Phillips screwdriver 0 Needle-nosed pliers Fig. 1 Strap switch - Preset Factory Setting Please vertfy the device configuration jumpers are set as shown below. Device confiauration jumpers The jumpers are preset at factory for all PC configurations. DO NOT change any of the default settings. Power connector Rear View Interface connector Pl;rl #l Fig. 2 -2- -3- HARDWARE INSTALLATION GUIDE HARDWARE INSTALLATION GUIDE HARDWARE INSTALLATION (continued) BEFORE YOU START System Requirements l IBM or IBM-compatible personal computer, 386 or higher processor. hi . Make a note of the orientation of the color stripe, indicating Pin 1 on the cable, then unplug this cable from the floppy controller. Match the color stripes on the two cables, then plug your floppy drive data cable into the second connector on the tape drive interface data cable. 10 Plug the remaining end of the tape drive interface data cable into the floppy controller card. Find any unused power cable inside your computer and plug it into the back of the tape drive unit. Follow the instructions inside the Arcada Backup User Guide, for installing the tape backup software, before you attempt to use your tape drive. t Tape Ejection 1. + Caution: To prevent the tape from becoming excessively loose and causing damage: DO NOT eject a tape while it is running and the LED is on. Write protection tab DO NOT switch the power off while a tape is running. After ejection, store the tape in a tape carrying case until it is to be used again. Insert this edde into tape drive -6- -7- . [. . . ] After ejection, store the tape in a tape carrying case until it is to be used again. Insert this edde into tape drive -6- -7- . HARDWARE INSTALLATION GUIDE SPECIFICATIONS Tape1600 Model: Recommended Media: Compressed: Uncompressed: Tape Format: Downward Read Compatibiltity: Speed: Data Transfer Rats: Interface: MTBk Dimensions: Weight: FT-301 OTR Travan TR-2 1. 6G8 EOOMB QIC-301 O-MC QIC-80, 1X-40 Tape800 FT3008TR Travan TA-1 EJOOMB 400MB QIC-EO-MC QIC40 Up to 95M8 per minute Dual Speed: SOOKbps and1 Mbps* Floppy 119, 000 POH 4YWl x IYHI x 5. 7"IDl . 99 Ibs. i 1 Mbps reqwes high-speed c~ntmller TAPE MEDIA COMPATIBILITY Tape1600 Minicartridge Compatibility Media Type: Format: Compressed 2:i Uncompressed: Tape Length: Brand Name: Jravan TR-2 QIQ 3010 1. 6GB 800MB 750 ft. [. . . ]