User manual THOMSON DPL5000

[. . . ] THOMSON 46, quai Alphonse Le Gallo 92648 Boulogne Cedex FRANCE TOCOM www. thomson. net DPL5000 Audio Video Receiver User's Guide Safety Information Rating Information: At bottom / back of the unit this unit comply with the existing requirements In accordance with the rating plate of the unit, this unit complies with current standards concerning electrical safety and electromagnetic compatibility. Please respect the environment Before throwing any batteries away, consult your distributor who may be able to take them back for specific recycling. Have a Blast- Just Not in Your Eardrums Make sure you turn down the volume on the unit before you put on headphones. Increase the volume to the desired level only after headphone are in place. THE LIGHTNING FLASH AND ARROWHEAD WITHIN THE TRIANGLE IS A WA R N I N G S I G N ALERTING YOU OF "DANGEROUS VOLTAGE" INSIDE THE PRODUCT. Table of Contents Safety Information RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] On the remote control, press the button twice within 2 seconds if the receiver is not in Tuner source mode to enter standby mode. To avoid entering standby mode when powering up the unit, do not press the button twice within 2 seconds. · The receiver draws a small amount of electricity when in standby mode. Example 2: Based on the example 1, the DVD is playing , if a VCR is connected to the VCR input (audio & video) of the receiver, press the SOURCE button on the main unit repeatedly until VCR is selected or press AUX 1 (VCR) on the remote control. The image and sound from the VCR source will replace the DVD. L C R · Dolby Digital audio input for signal format. LS LFE RS · Dolby Pro Logic II audio output format. · Speaker Icons. L - Front left speaker C - Center speaker R - Front right speaker LS - Left surround (rear) speaker RS - Right surround (rear) speaker LFE - Subwoofer speaker SUBWOOFER SOURCE SURROUND · DTS audio output format. P SLEEP · Unit in Sleep mode. Selection of Audio/Video source When one of the source buttons is pressed, the audio and video input corresponding to the name will be activated. The receiver acts as a switching device between all the sources that are plugged into it. FM / AM · Radio band indicator in Tuner mode. MEMORY · Unit is ready to store a station in selected preset. ST · Tuner stereo signal selected. RDS · Radio data system information is received. SUBWOOFER SOURCE SURROUND OPT 1 2 · Optical digital input selected. KHz / MHz · Tuner frequency unit. COAX · Coaxial digital input selected. 12 13 Operating your Receiver You can connect up to 6 audio/video sources to this amplifier: Source button (receiver front panel) DVD VCR SAT CD TAPE TV TUNER Corresponding connector (receiver back panel) DVD IN (audio / video) VCR IN/OUT (audio / video) SAT IN (audio / video) CD IN (audio only) TAPE IN/OUT (audio only) TV IN (audio only) built-in Operating your Receiver Using the Remote to Control Additional Components You can use your remote to control most of Thomson branded VCRs, satellites, cable boxes or TVs. Press the corresponding source button on the remote control to operate options on other components. Volume Punchthrough NOTE Volume punchthrough can be done in all non-Tuner modes. By default, the VOL+/VOL- and MUTE buttons will only control the receiver, regardless which mode (TV, VCR, etc) the receiver is in. By programming the volume punchthrough function, you can also control the volume of the TV. To activate the volume punchthrough function, follow the procedures below: 1. While holding down the VOL- button, press one of the source buttons to select the source where you want to control TV volume at. You should now be able to control TV volume and mute at the selected device. NOTE Some DVD players may require you to set the digital output format to get Dolby Digital and DTS signals through digital connection to the receiver. 2. Press ON/ECO on the main unit or press remote control to switch on the receiver. on the EN An arrow points to the source name selected shown on the display. Example : If you have connected a DVD player to the DVD input (audio & video) on the receiver, press the SOURCE button on the main unit repeatedly until DVD is selected or press DVD·6CH on the remote control to receive the sounds and images transmitted by the DVD. 3. Press the SOURCE button repeatedly on the main unit or DVD·6 CH on the remote control to select the DVD source. Select the appropriate A/V channel on the TV (refer to your TV manual for details) until the image from the DVD player is displayed. Set the Surround Mode if needed (see "Advanced sound control" for details). NOTE 1. Just connect the appropriate antenna to the back of the receiver and you will be able to listen to radio stations. Refer to the "Connecting To Audio-Visual Components" section for details on connection. HINT To return to controlling receiver volume and mute again, follow the steps above but press TUNER instead of TV in step 3. NOTE To receive VCR signal for recording, you must connect analog outputs from DVD/CD/SAT/TV to the analog inputs of the receiver. HINT If batteries are removed from the battery compartment of the remote control, the volume and mute control in all source modes will be the receiver volume and mute control except in TV mode Example 1: To play Dolby Prologic II Movie sound Press the SURROUND buttons until "Dolby PL II MOVIE" appears on the Display and all of the speaker'' icons light up. Example 2: LD: You may need to select a different Audio Channel on your LD (refer to your LD player manual). Adjust the volume knob accordingly. Using the receiver to play a source After having properly connected a source (DVD, CD, VCR) to the receiver, you can partly control them through the receiver. Playing a DVD with the receiver 1. [. . . ] · Check that the headphone is not inserted. Disconnect the audio system from the power source before performing any maintenance. Equipment Specifications: AMPLIFIER SECTION: RMS Output Power: Dolby Digital Mode with 10% Total Harmonic Distortion Rear Channels: 60 Watts each Channel (1KHz, 8 Ohm) Front Channels: 120 Watts each Channel (1KHz, 4 Ohm) Center Channel: 120 Watts (1KHz, 4 Ohm) Subwoofer Channel: 120 Watts (100Hz, 4 Ohm) Total RMS Output Power, Dolby Digital mode : 600 W DIN Output Power: Dolby Digital Mode with 1% Total Harmonic Distortion Front Channels (L and R ): 48 Watts per Channel (1KHz, 4 Ohm) Rear Channels (L and R): 24 Watts per Channel (1KHz, 8 Ohm) Center Channel: 48 Watts (1KHz, 4 Ohm) Subwoofer Channel: 48 Watts (80Hz, 4 Ohm) Total DIN Output Power, Dolby Digital mode: 550 Watts Muting Attenuation: 65dB Frequency Response: 20kHz /-3dB, 1kHz ref. DIN 1kHz FL / FR STEREO mode : 45W x2 @ 6ohm <10% THD Signal to Noise Ratio: 65dB (Dolby digital mode) Video Signal to Noise Ratio from 40 dB to 60dB Cleaning Clean the exterior of the system using a soft dust cloth. EN Important battery information · Remove the batteries to avoid leakage if you do not use your remote control for more than one month. · Discard leaky batteries immediately as leaking batteries may cause skin burns or other personal injuries. · Dispose of batteries in the proper manner, according to provincial and local regulations. [. . . ]