User manual THOMSON DPL560

[. . . ] DPL560-EN 4/11/02 5:27 PM Page 2 EAT HOME TH ON/ECO SOURCE MUTE AL DIGIT SOURCE PHONES Thomson multimedia 46/47 quai A. Le Gallo 92648 Boulogne Cedex FRANCE RCS nanterre B322 019 464 55199360 www. thomson-multimedia. com DPL560-EN 4/11/02 5:27 PM Page 3 u s e r m a n u VOLUME ER E THEAT CEIVE IDEO RE AUDIO V 0H R DPL56 T a SURR MODE DIGITAL INPU T DSP MODE LEVEL BASS/TREBLE OK SETUP TEST TONE EQ SOURCE BAND SOURCE TUNING MEMORY ST / MONO V-AUX VIDEO L - AUDIO - R DPL560 l DPL560-EN 4/11/02 5:27 PM Page 4 Safety Information For UK Only CONNECT THE MAIN LEAD INTO A MAINS POWER SOCKET POWER SUPPLY 230V. If the mains socket are not compatible or if for any reason the plug is removed please follow the directions below. The molded plug cannot be rewired and if removed must be disposed of safely. [. . . ] The remote control currently operates most Thomson, RCA and GE products. 6 11 9 9. DIGITAL Select the way your audio/video components are connected to the receiver (Analog, Optical or Coaxial). · Press TUNER UP and TUNER DOWN keys to tune down or up the radio frequency. 8 11. SURR (Surround Sound Control) Press to change the surround sound settings. HIFI/DVD Press the appropriate key to control either the receiver or a compatible DVD player (Thomson brand only) Note: After pressing DVD, you must press HIFI to enable all receiver functions on the remote. 11 DPL560-EN 4/11/02 5:27 PM Page 16 Operating Your Receiver Display DTS · Audio output is in DTS mode. SLEEP · Unit in Sleep mode. · Audio output is in Dolby Digital mode. MEMORY · Unit in Memory mode. · Audio output is in Dolby ProLogic mode. ST · Tuner stereo signal detected. KHz MHz RDS · Tuner frequency unit. TUNED · Tuner station detected. L C R · Radio data system is available. LS LFE RS · Speaker Icons. 12 DPL560-EN 4/11/02 5:28 PM Page 17 Operating Your Receiver Switching on/off · To switch on the receiver, press ON/ECO button once, or any source button on the remote control. Selection of Audio/Video source When one of the source buttons is pressed, the audio EN and video input corresponding to the name will be activated. The receiver acts as a switching device between all the sources that are plugged into it. ON/ECO SOURC MUTE SOURC DIGITAL PHONES SOURCE FM/AM SOURCE L TUNING MEMORY · Standby: when the receiver is on, press the ON/ECO button once to activate the standby mode. · To switch off the unit completely, unplug the power cord from the socket Example 1: If you connect a DVD player to the DVD input (audio + video) on the receiver and press the source button repeatedly until DVD is selected, you will be able to have the sound and image transmitted by the DVD. Example 2: SOURCE FM/AM SOURCE L TUNING MEMORY NOTE Your receiver has a back up memory to keep your settings like preset radio station for about 2 weeks in case electricity outage occurs. If the receiver is unplugged for more than 2 weeks, all the settings will be lost and reset to factory settings. Based on the example 1, the DVD is playing , if a VCR is connected to the VCR 1 input (audio + video) of the receiver, press the VCR/VAUX button , or press source button repeatedly until VCR is selected, image and sound from the VCR source will replace the DVD. SOURCE FM/AM SOURCE L TUNING MEMORY 13 DPL560-EN 4/11/02 5:28 PM Page 18 Operating your Receiver You can connect up to 7 audio/video sources to this amplifier: Source button Corresponding connector (receiver front panel) (receiver back panel) DVD SAT VCR VAUX CD TV TAPE FM/AM DVD IN (audio / video) SAT IN (audio / video) VCR IN (audio / video) V-AUX IN (audio / video) CD IN (audio only) TV IN (audio only) TAPE IN (audio only) built-in When a source is selected, the source name will be shown on the display. NOTE 1. Just connect the appropriate antenna on the back of the receiver and you will be able to listen to radio stations. Refer to the "Connecting To Audio-Visual Components" section for details on connection. 14 DPL560-EN 4/11/02 5:28 PM Page 19 Operating your Receiver Using the receiver to play a source After having properly connected a source (DVD, CD, VCR) to the receiver, you can partly control them through the receiver. EN Playing a DVD with the receiver 1. Connect a DVD player to the receiver (see connecting your receiver for details) NOTE To play Dolby Digital sound / DTS, the source must be connected to the receiver via the optical or coaxial terminal 2. Select the appropriate A/V channel on the TV (refer to your TV manual for details) until the image from the DVD player is displayed 7. Set the sound Mode if needed (see "Advanced sound control" for details) Example 1: To play 5. 1 Dolby Digital surround sound Press SURR. MODE button until "Dolby Digital" appears on the Display and all of the speakers'' icons light up. Example 2: DVD: You may also need to select the Dolby Digital 5. 1 on the DVD disc menu to have the digital surround enabled providing that the disc is encoded with Dolby Digital 5. 1 (please refer to the DVD player and DVD disc instruction) Example 3: LD: You may need to select a different Audio Channel on your LD (refer to your LD player manual) 8. Adjust volume knob accordingly 15 DPL560-EN 4/11/02 5:28 PM Page 20 Operating your Receiver Operating the Radio The receiver has a built-in tuner that allows for AM/FM radio function. 5- Tune the stations by pressing TUNING UP or DOWN repeatedly until the desired station is found. Alternatively, you can press and hold TUNING UP or DOWN for about one second to activate the automatic SEARCH function. In this mode the receiver will automatically tune frequencies until it finds a station Manual tuning 1. Connect the FM and AM antenna accordingly (see "Connecting the Antenna" on page 5 section for details) E 2. [. . . ] · Check if the video and audio cable are correctly inserted. EN Cleaning the Exterior · Disconnect the system from AC power before cleaning the exterior of the system with a soft dust cloth, or with a slightly damp leather chamois. · Adjust Antenna · Reposition Antenna away from any electronics. Equipment Specifications: AMPLIFIER SECTION: All 5 channels: each 50W at 8 ohm. <10% THD @1 kHz Subwoofer channel: 50w at 8 , <10% THD @100 kHz Muting Attenuation: 65dB Frequency Response: 40Hz to 20kHz +/-3dB Signal to Noise Ratio: 65dB (Dolby digital mode) Remote Control Operation The remote control does not operate the unit. · Another source mode is selected on the remote. (included with your system) Install the batteries before attempting to operate the remote. [. . . ]