User manual THOMSON DPL660

[. . . ] Le Gallo 92648 Boulogne Cedex FRANCE RCS nanterre B322 019 464 55302970 Rev. 1 www. thomson-multimedia. com u s e r m a n VOLUME ECEIVER AUDIO VIDEO R H O M E T H E AT E R u ON/ECO SURR MODE SOURCE BAND MUTE SOURCE TUNING MEMORY OK SETUP TEST TONE EQ DIGITAL INPUT DSP MODE ST / MONO BASS/TREBLE LEVEL a V-AUX VIDEO L - AUDIO - R PHONES DPL660HT l Safety Information Rating Information: At bottom of the unit this unit comply with the existing requirements In accordance with the rating plate of the unit, this unit complies with current standards concerning electrical safety and electromagnetic compatibility. Please respect the environment Before throwing any batteries away, consult your distributor who may be able to take them back for specific recycling. Have a Blast- Just Not in Your Eardrums Make sure you turn down the volume on the unit before you put on headphones. Increase the volume to the desired level only after headphone are in place. THE LIGHTNING FLASH AND ARROWHEAD WITHIN THE TRIANGLE IS A WA R N I N G S I G N ALERTING YOU OF "DANGEROUS VOLTAGE" INSIDE THE PRODUCT. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] The remote control currently operates most Thomson, RCA and GE products, but it can be programmed to operate devices from other manufacturers MULTI PRODUCT rc 1000 NOTE Remote control selector must be on hifi. 1. ON/OFF To turn on or off the receiver and other auxiliary components (see page 14 "Using the Remote to Control Additional Components"). Digital Select the way your SAT external audio/video devices are connected to the receiver (Analog, Optical or Coaxial) through the SAT audio input. In Tuner mode, press to toggle between stereo and mono sound. 11 Operating Your Receiver Display C R S RS DVD / VCR / SAT / TUNER / TAPE / V-AUX / C D / TV · The arrow points to the repective icon to show the current source. COAX · Coaxial digital input detected. ST · Tuner stereo signal detected. · Audio output is in Dolby Digital mode. TUNED · Tuner station detected. · Audio output is in Dolby Pro Logic mode. SLEEP · Unit in Sleep mode. · Audio output is in Dolby Pro Logic II mode. EQ · EQ effect activated. · Audio output is in dts mode MEMORY · Unit in Memory or Preset mode. RDS · Radio data system is activated. FM / AM / MW / LW · The repective tuner icon will lite showing current radio frequency. KHz / MHz · Tuner frequency unit. OPT12 · Optical 1 or 2 digital Input detected L C R LS LFE RS · Speaker Icons. 12 Operating Your Receiver Switching on/off · To switch on the receiver, press ON/ECO button once, or any source button on the remote control. digital dvd/ cd 6 channel stereo dts tape sat/cab tape sat/cab MUTE theater modes delay up level Example 1: If you connect a VCR player to the VCR input (audio + video) on the receiver and press the SOURCE or button on the main unit until VCR1/ANL shows on the display. You can also press vcr/V. AUX on the remote to select the source directly. You will be able to have the sound and image transmitted by the VCR. dvd/ cd 6 channel stereo dts up delay level EN ON/ECO tuner V. AUX RDS digital dvd/ cd 6 channel stereo dts tape sat/cab vcr/ tuner V. AUX hifi dvd /cd vcr/ SOURCE BAND SOURCE TUNING M vcr/ tuner V. AUX hifi dvd /cd theater modes delay up level pty down RDS tv vcr/sat rep. mix NOTE pty RDS Remote control selector must be on vcr/sat to operate VCR features. · Standby: when the receiver is on, press the ON/ECO button once to activate the standby mode. · To switch off the unit completely, unplug the power cord from the socket. Example 2: Based on example 1, the VCR input is selected. If SAT is selected, image and sound from the SAT source will replace the VCR. theater modes stereo dts tape sat/cab up delay level digital Selection of Audio/Video source When one of the audio/video source is selected, the audio and video input corresponding to the name will be activated. The receiver acts as a switching device between all the sources that are plugged into it. SOURCE BAND SOURCE TUNING M dvd/ cd 6 channel vcr/ tuner V. AUX RDS NOTE Remote control selector must be on vcr/sat to operate SAT features. digital SOURCE BAND SOURCE TUNING M theater modes stereo dts up delay level dvd/ cd 6 channel tape sat/cab vcr/ tuner V. AUX hifi dvd /cd pty RDS NOTE Remote control selector must be on hifi. 13 Operating your Receiver You can connect up to 7 audio/video sources to this amplifier: Source button Corresponding connector (receiver front panel) (receiver back panel) DVD SAT VCR V-AUX CD TV TAPE FM/AM DVD IN (audio / video) SAT IN (audio / video) VCR IN/OUT (audio / video) V-AUX IN (audio / video) CD IN (audio only) TV IN (audio only) TAPE IN/OUT (audio only) built-in Using the receiver to play a source After having properly connected a source (DVD, CD, VCR) to the receiver, you can partly control them through the receiver. Playing a DVD with the receiver 1. Connect a DVD player to the receiver (see connecting your receiver for details) NOTE To play Dolby Digital or DTS sound, the source must be connected to the receiver via the optical or coaxial terminal When a source is selected, the arrow will point to the source name on the display. Example: Press DVD to select DVD as the source to the amplifier. NOTE 1. Just connect the appropriate antenna on the back of the receiver and you will be able to listen to radio stations. Refer to the "Connecting To Audio-Visual Components" section for details on connection. 2. Select the appropriate A/V channel on the TV (refer to your TV manual for details) until the image from the DVD player is displayed 7. Set the sound Mode if needed (see "Advanced sound control" for details) Example 1: To play 5. 1 Dolby Digital surround sound Press SURR. MODE button until "Dolby Digital" appears on the Display and all of the speaker'' icons light up. Example 2: DVD: You may also need to select the Dolby Digital 5. 1 on the DVD disc menu to have the digital surround enabled providing that the disc is encoded with Dolby Digital 5. 1 (please refer to the DVD player and DVD disc instruction) Example 3: LD: You may need to select a different Audio Channel on your LD (refer to your LD player manual) 8. Adjust volume knob accordingly 14 Operating your Receiver Operating the Radio The receiver has a built-in tuner that allows for AM/FM radio function. [. . . ] · The remote is not pointed at the remote control sensor on the main unit or there is an obstacle between the remote and the main unit. · The remote control is too far from the main unit, move closer. AMPLIFIER SECTION: All 5 channels: each 100W at 8 ohm. <0. 9% THD @40Hz to 20KHz Subwoofer channel: 150w at 8 , < @100 Hz Muting Attenuation: 65dB Frequency Response: 40Hz to 20kHz +/-3dB Signal to Noise Ratio: 65dB (Dolby digital mode mode) VIDEO SECTION: Input ( Sensitivity/ Impedance ):1Vp-p/ 75ohm Output (Level/ Impedance): 1Vp-p/ 75 ohm Frequency Response: 10Hz to 6MHz at +/- 3dB Signal to noise ratio: 40dB Crosstalk @3. 58MHz: 40dB Remote loses Programmed codes. · Weak batteries, replace batteries. AM TUNER SECTION: Frequency Response: 80Hz ­ 2kHz +/-6dB Usable Sensitivity: 800uV/m @ S/N 20dB Signal to Noise: 38dB Image Ratio: 27dB @ 1000kHz IF Rejection: 35dB Remote forgets what source was selected. · Weak batteries, replace batteries. General No audio. · Make sure the speakers are connected. · Make sure the digital setting (optical, coaxial or analog) is correct. [. . . ]