User manual THOMSON RR220PLL

[. . . ] DO NOT under any circumstances plug the severed plug into any mains socket as this could result in electric shock. Important: If the plug is removed, rewire the new plug as follow: The wires in the mains plug are coloured in accordance to the following code: BLUE = NEUTRAL & BROWN = LIVE If the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: BLUE wire to the terminal coded N (Neutral) or coloured black. DO NOT make any connection to the terminal in the plug which is marked by the letter E or by the earth symbol or coloured green BLUE BROWN or green and yellow. [. . . ] When normal household power is interrupted, or AC line cord is unplugged, the battery will power the clock radio to keep track of time and alarm settings programmed into memory. When the battery backup functions, the digital display will not be backlighted, however, the function of alarm still occurs during the power interruption if remaining battery power is adequate. Normal operation will resume after AC power is restored so you will not have to reset the time or the alarm. Remove battery compartment door (located at the bottom of the radio) by applying thumb pressure to area indicated on battery door and then lift the door out and off the cabinet. Insert battery in the compartment and replace the compartment door. Power Failure Indicator When AC power is interrupted (disconnected) for a short period of time, both time and alarm settings will change (unless optional battery is installed). After AC power is restored (reconnected), the Digital Display will blink to indicate that power was interrupted and you should readjust the time and alarm settings. Note: Alkaline (NEDA 1604A / IEC 6LR61) battery is recommended. Carbon Zinc (NEDA 1604 / IEC 6F22) battery may be used but memory holding time will be substantially reduced. Memory holding time for a fresh alkaline battery is approximately 8 hours (if radio or alarm is not operated), which should take care of short, nuisance-type AC power failures. To preserve battery life, the radio should remain plugged into an AC outlet. Battery should be removed if the radio will be stored for more than one month. Leaky batteries may badly damage the clock radio. 2 RR220PLL/M EN 3 5/17/02, 4:33 PM Operating the clock EN Setting Clock Time Your digital clock operates on a 24 hour standard mechanism. Setting the Wake Time 1. Press the SET button once to set ALARM 1 (1 will flash on display), twice to set ALARM 2 (2 will flash on display). You can exit set mode by pressing SET button until no flashing sign or clock icon is displayed. 1. Press to set the hour, and to set minute. Example 1: ALARM 1 mode setting: 8:50 AM Wake to Alarm Example 2: ALARM 2 mode setting: Alarm off 3 RR220PLL/M EN 4 5/17/02, 4:33 PM Operating the Clock EN Waking by Selected Source Programme You may be woken up by music or . Press the ALARM 1 or ALARM 2 button to select waking up by music or alarm. Press SLEEP to read the remaining sleep time. Nap Mode This function wakes you up after a short period of time. Press NAP once to show time left. by pressing O F F the F, or the music will turn on at alarm the same time tomorrow. Note: The unit equips with GRAD-UWAKE feature, the alarm tone volume will increase gradually to its maximum in about 30 to 45 seconds. (Volume level cannot be adjusted in GRAD-U-WAKE mode) Stop the Nap alarm Press NAP or follow "Turning off Alarm". [. . . ] Then the alarm will be on the following day at the same time. Disable the alarm permanently 1. Press ALARM 1 or ALARM 2 button within 3 seconds to deactivate the alarm function permanently, "OFF" will be shown when the above procedures are done. Tip: You can activate the previously set alarm time by pressing ALARM 1 or ALARM 2 button. Brightness control You can adjust the backlight by the DIMMER button, there are three modes you may select from: AUTO - Backlight on for a few seconds whenever a button is pressed. [. . . ]