User manual THOMSON SPEEDTOUCH HOME

[. . . ] 04 Status Change Note Released BD F aa 31244 Short Title CD-UG STHome All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 2 / 104 3EC 17058 AAAA TCZZA Ed. 11 12 16 17 18 20 21 22 23 24 25 27 29 30 31 33 37 39 40 41 44 46 49 50 52 54 55 56 57 58 59 61 64 2 Speed Touch Configuration Guide . 04 3 / 104 Contents 7 8 9 Maintenance - Speed Touch Software . [. . . ] The use , of these IP addresses is limited to the local network. Private IP addresses You are free to choose any IP address as long as it is compatible with your local network and is unique in that same network. As the STHome has a preconfigured Net10" address (10. 0. 0. 138), you should configure IP addresses like 10. 0. 0. 1, 10. 0. 0. 2, . . . on your PCs. Note: IP addresses can be configured automatically via STHome's DHCP server. See section 6. 3 for more information. Public IP addresses A second set of (Public) IP addresses having end to end scope will automatically be negotiated via the PPP protocol inside your PC(s). Simultaneous use of public & private IP Both Public and Private IP addresses are active simultaneously because of tunneling. In fact two nested" IP layers exist: the Public IP layer which is carried within the Private IP layer on the local LAN. PPP IP address negotiation By default the PPTP tunnel application automatically negotiates the Public IP address. In case your SP instructs you to use a static IP address for Relayed PPPoA, most dial in applications allow a static IP address to be supplied. 58 / 104 3EC 17058 AAAA TCZZA Ed. 04 6 Networking Services - IP DHCP and DNS , 6. 2 Speed Touch Addresses Introduction Like any other member of a LAN, the STHome must be locally identified by an IP address to be able to communicate with other local LAN devices. This section deals with the IP address configuration of the STHome for local communication only. Assigning IP addresses to the STHome IP addresses can be assigned to the STHome in several ways. Summarized, following IP address types exist: " " " " The default IP address: 10. 0. 0. 138 IP addresses assigned via the 'Initial Setup' page IP addresses assigned via a 'Ping of LifeTM IP addresses assigned to the STHome via DHCP . STHome and multiple IP addresses As the STHome IP layer supports logical multi homing (one interface supporting multiple IP addresses), both statically and dynamically configured IP address(es) can be active at the same time. 'IP address' table On the STHome 'Routing' page the 'IP address' table summarizes all IP addresses configured on any of the STHome interfaces. 3EC 17058 AAAA TCZZA Ed. 04 59 / 104 6 Networking Services - IP DHCP and DNS , Setting an IP address via the 'Initial Setup' page Proceed as follows: 1. Click in the left pane of the STHome pages to pop up the 'Initial Setup' page: 2. Enter a netmask for applying subnetting in your network in the 'Subnetmask' field. to store the applied IP settings to permanent Sample configuration: single PC In the below figure, a simple configuration is given: One PC attached to the STHome: IP address : 10. 0. 0. 138 (Sub)netmask : 255. 255. 0. 0 Default Gateway : none IP address : 10. 0. 0. 1 (Sub)netmask : 255. 255. 0. 0 Default Gateway : none IP Network 10 60 / 104 3EC 17058 AAAA TCZZA Ed. 04 6 Networking Services - IP DHCP and DNS , 6. 3 Speed Touch DHCP DHCP Depending on the size and complexity of your network, a few DHCP configurations can be envisaged: LAN Type Simple Medium sized DHCP Mode No Server Argumentation All few members of the small LAN have static IP addresses, including the STHome. For small home LANs it might be worthwhile to configure all of your LAN devices as DHCP clients, and the STHome as the DHCP server. In this configuration each time a computer starts, it will obtain its IP configuration from the STHome. Advanced Client For advanced networks, the role of DHCP server might be performed by an IP node other than the STHome on the local LAN. Default STHome DHCP The 'DHCP' page Per default the STHome DHCP server is disabled. Click in the left pane of the STHome pages to pop up the 'DHCP' page: 3EC 17058 AAAA TCZZA Ed. 04 61 / 104 6 Networking Services - IP DHCP and DNS , 'DHCP Server Start up Mode' radiobuttons The 'DHCP Server Start up Mode' radiobuttons allow to configure the STHome DHCP server mode. Configuring the STHome for a LAN without DHCP To setup the STHome without DHCP tick , . In this configuration, it is assumed that all members, the STHome included, have static IP addresses. See subsection 6. 2 for static IP addressing of the STHome. Note: This configuration might be required in case you use the Transparent Bridging packet service. Configuring the STHome as DHCP server To setup the STHome as DHCP server, tick . Via the 'DHCP Server Configuration' tables, you can configure the STHome DHCP server settings. Internet IP Address ATM Network Access Point STHome DHCP Server Note: This setting might cause side effects with Bridging. See section 6. 1. 1 for more information. Configuring the STHome as DHCP client To setup the STHome as DHCP client, tick 'DHCP' page. Internet STHome ATM Network Access Point IP Address IP Address on the DHCP Client DHCP Server 62 / 104 3EC 17058 AAAA TCZZA Ed. 04 6 Networking Services - IP DHCP and DNS , Configuring the STHome for Auto DHCP One of the STHome features is that it can automatically revert from DHCP client to DHCP server. At boot time the STHome probes the LAN for a specified time limit ('Client timeout') to check whether another DHCP server is available on the network. [. . . ] 04 101 / 104 AppendixD Safety and Agency Regulatory Notices D. 2 European Community Declaration of Conformity Products with the marking comply with both EMC and Low Voltage Directives issued by the Commission of the European Community. EC Declaration of Conformity A copy of the European Community Declaration of Conformity is provided in your Speed TouchTM product shipping box. 102 / 104 3EC 17058 AAAA TCZZA Ed. 04 AppendixD Safety and Agency Regulatory Notices D. 3 Radio Frequency Interference Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against such interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. [. . . ]