User manual THOMSON WFT5110 INSTALLATION

[. . . ] In the THOMSON product range, you will also find a wide choice of ovens, cooking hobs, ventilation hoods, dryers, dishwashers, fridges and freezers, that you can coordinate with your new THOMSON washing machine. Of course, we always wish to meet your requirements regarding our products as best we can, and our customer services are therefore at your disposal and ready to listen and answer any questions or suggestions you may have. For all our products, as well as useful and additional information, you can also visit our website. This machine is only for domestic use and is designed to wash, rinse and spin machine-washable textiles. [. . . ] Adjust the dosage correctly to the weight of the washing you have placed in the machine. These recommendations will help you to avoid using too much detergent, which causes foam to be produced. Too much foam can reduce your machine's performance and increase the length of the washing cycle and the consumption of water. Use a spirit level to check that the floor is horizontal: maximum slope 2°, i. You are recommended to use an appropriate detergent for washing these fabrics (avoid placing such detergents directly on the drum because they have an aggressive action on the metal). Some machines are fitted with two adjustable feet at the front to enable you to compensate for any unevenness in the floor. Proceed as follows to adjust the feet to level and stabilize your machine: -- Set the machine on its castors (or tilt it slightly backwards if it does not have retractable castors) -- Screw in or unscrew the feet to adjust the height to suit the shape of the floor (Diagram D13) -- Set the machine back on its feet and check that it is stable. Before your first wash Before making your first wash, we recommend that you carry out a "COTTON 90 wash without pre-wash" and with no washing in the drum, using a 1/2 measure of your usual detergent in order to eliminate any residues from manufacturing that may remain in your machine. To comply with the statement on the label, the tests are conducted in accordance with European Directive 95/12/EEC. -- Washing : Never exceed the indicated temperatures -- Use of cold diluted bleach possible: cl -- Iron: Low Medium High -- Dry clean: mineral spirit perchlorethylene all solvents -- NB: A crossed-out code indicates that it is forbidden All the buttons are on microswitches and do not remain depressed. In any case, the "Start/Pause" button cannot cancel a programme. Then press the button again and briefly press "Start/pause" 5 . - If you want to reduce the length of time of the delayed start, proceed in the same way but do not press the "Start/Pause" button 5 . -- You can only activate the "Prewash" , "Extra rinse" and "Surfliss" options during a delayed start's waiting period. This option washes your laundry more gently, but with an identical washing performance. This function, for very delicate linen, enables you to remove spinning and to pass directly to the draining of the washing machine. You can delay the start of your programme by 1 to 19 hours so that you can benefit from cheap rate electricity or to have the cycle finish at a desired time. To do this, select the time that must pass before the cycle starts by pressing successively on button 3 (this is done hour by hour) and then press "Start/Pause" 5 . NB: - Even if you forget to press the "Start/Pause" button after selecting this option, your choice will still be accepted after a few seconds. - The time remaining before the start of the cycle is counted down hour by hour from 19 hours to 1 hour and then minute by minute from 59 minutes to 1 minute. - Throughout the whole waiting period, the delayed start symbol is displayed and the four elements light up in succession. When the screen A shows "- 0 -", you can programme a new cycle without having to reset the selector 1 to the "OFF" position. [. . . ] Your machine automatically detects some operating incidents and indicates these by particular messages shown on the screen. Check that the water tap is open and then press the "Start/Pause" button again to restart the cycle. This incident may also be caused by the drain hose being poorly connected (see the section "DRAINING AWAY THE WASTE WATER"). Clean the pump filter (for how to do this, see the section "CLEANING THE PUMP FILTER") and then press the "Start/Pause" button again to restart the cycle. [. . . ]