User manual THUNDER TIGER SLEDGE HAMMER S50

[. . . ] Read these Instructions carefully before installing or using the Ventilation System. Use the appliance only for its intended purpose. , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: ~ a) Use this appliance only in the manner intended by the manufacturer. appliance, switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally. If the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. [. . . ] The lighting however will remain on. ^ Press the On/Off button to turn the fan back on again. 12 Operation Turning the lighting On/Off The overhead lighting can be turned on and off independently from the fan. Dimming the lighting The brightness of the lighting can be adjusted. ^ If the button is pressed again, the lighting will brighten until the button is released. If the button is pressed continuously, the light will cycle between bright and dark. If the procedure is not stored within 4 minutes of programming, the hood will automatically default to the "old" data. ^ Press the On/Off button to turn off the fan. ^ Press the Delayed Shut Down and grease filter buttons at the same time. The indicator for the grease filter and one of the "­/+" indicators will flash. 15 Operation Reprogramming the charcoal filter timer The active charcoal filter can only be used in recirculation mode and cannot be used to exhaust fumes. Before using the hood in recirculation mode, the charcoal filter timer must be programmed. The lit indicator shows the programmed time: 1st indicator from the left 2nd indicator from the left 3rd indicator from the left 4th indicator from the left = = = = 20 hours 30 hours 40 hours 50 hours ^ Use the "­/+" button to select the desired time. ^ Press the Delayed Shut Down and charcoal filter buttons at the same time. The indicator for the charcoal filter and one of the "­/+" indicators will flash. If the procedure is not stored within 4 minutes of programming, the hood will automatically default to the "old" data. 16 Cleaning and Care , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before cleaning or servicing the hood, disconnect it from the power supply, see "Important Safety Instructions". Avoid: ­ cleaning agents containing soda, acids or chlorides, ­ abrasive cleaning agents e. g. pot scourers or sponges which have been previously used with abrasive cleaning agents. These will damage the surface. Cleaning the casing Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the hood. 6 seconds to reset the counter to zero. 19 Cleaning and Care Changing the light bulb , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before changing the light bulbs, disconnect the hood from the power supply, see "Important Safety Instructions". ^ Return the grease filters. When in use halogen bulbs become extremely hot, use caution. Do not attempt to change the bulbs until they have had sufficient time to cool. Fingerprints or body oils deposited on the bulb will decrease its life. The halogen lamp will swivel down. 20 After Sales Service Repairs In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department. ^ When contacting the Technical Service Department, please quote the model and serial number of your appliance. These are shown on the data plate which is visible when the grease filters are removed. MieleCare (USA only) MieleCare, our Extended Service Contract program, gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership. MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts. Only genuine Miele parts installed by factory trained professionals can guarantee the safety, reliability, and longevity of your Miele appliance. Please note that unless expressly approved in writing by Miele's Service department, Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele. Our goal is to prevent unauthorized (and untrained) service personnel from working on your Miele products, possibly doing further damage to them, you and/or your home. [. . . ] If several gas surfaces are installed under the hood, the total output must be considered when determining the minimum safety distance. Be sure to follow the minimum safety distances given by the gas cooktop manufacturer to easily flammable materials e. g. If local building codes require a greater safety distance, follow their requirement. If there is more than one appliance beneath the hood and they have different minimum safety distances always select the greater distance. [. . . ]