User manual THUNDER TIGER ST-1

[. . . ] appliance, switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally. If the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. To guarantee the electrical safety of this appliance, continuity must exist between the appliance and an effective grounding system. If there is any doubt, have the electrical system of the house checked by a qualified electrician. ~ b) Before servicing or cleaning the ~ This appliance is intended for ~ This appliance complies with current safety requirements. [. . . ] ­ to show how long the grease filter has been in use (see "Operation / Grease filter timer"). ­ to change the number of hours counted by the grease filter timer (see "Operation / Reprogramming the grease filter timer"). h On/Off button i Fan power level buttons Four fan speed selection. j Delayed Shut Down This button activates the Delayed Shut Down feature. The fan can be set to turn off automatically after either 5 or 15 minutes. 9 Operation Turning on the fan Automatically switching back the intensive power level The intensive level "4" can be programmed to automatically switch back to level "3" after 10 minutes. ^ Turn the fan and the lights off. ^ Press the On/Off button. Selecting the power level ^ Use the "­/+" controls to select the desired power level. + = increases the fan speed ­ = decreases the fan speed Levels "1" to "3" (green indicators) are usually sufficient for normal cooking. Intensive setting Level "4" (yellow indicator) should be used for a short period when frying or cooking food with a strong aroma. ^ Press and hold the "Delay Shut down" button for 10 secs. ^ Press the following buttons one after another, ­ light ­ the "­" button, and ­ the light button again. 10 Operation Fan performance The maximum air flow capacity is 625 cfm. Factors such as narrow duct diameter and bends will affect this value. Level 1 operates at 40% capacity Level 2 operates at 60% capacity Level 3 operates at 80% capacity Level 4 operates at 100% capacity If the power level indicators "1" and "4" flash, the automatic switch back is not activated. ^ To activate the automatic switch back press the "+" button. The power level indicators "1" and "4" light continuously. Removing the grease filter The grease filter and the air intake panel should be cleaned every 3 - 4 weeks or whenever the grease filter indicator lights red. , A dirty filter is a fire hazard. ^ To remove the grease filter pull the locking clip forward. Support the grease filter so that it does not fall onto the cooktop. 18 Cleaning and care Cleaning the grease filter ^ By hand: use a scrub brush with a solution of warm water and mild detergent. Do not use the pure detergent, aggressive all purpose cleaners, oven sprays, abrasive cleaning agents or limescale removers. ^ In a dishwasher: place the filter vertically in the lower basket, making sure that the spray arm is not blocked. Depending on the detergent, cleaning the grease filter in a dishwasher may cause permanent discoloration of the filter surface. ^ While the filter is removed, clean any dirt or grease from the interior casing to prevent the risk of fire. ^ When putting the grease filter back make sure that the locking clip is facing the cooking surface. ^ If the filter is incorrectly installed, insert a small screwdriver into the slit along its edge to disengage it from the casing. ^ After returning the grease filter, press the grease filter button for 3 seconds to reset the timer. ^ If the grease filter is cleaned before the grease filter timer has reached its maximum, the grease filter button should be pressed for 6 seconds to reset the counter to zero. 19 Cleaning and care Changing the light bulbs , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before changing the light bulbs, disconnect the hood from the power supply, see "Important Safety Instructions". When in use halogen bulbs become extremely hot, and can burn your hands. Do not attempt to change the bulbs until they have had sufficient time to cool. Fingerprints or body oils deposited on the bulb will decrease its life. ^ Flip the light cover back up, making sure it clicks into place. 20 After Sales Service Repairs In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department. [. . . ] ­ Be sure to follow the minimum safety distances given by the gas cooktop manufacturer to easily flammable materials e. g. ­ If local building codes require a greater safety distance, follow their requirement. ­ If there is more than one appliance beneath the hood and they have different minimum safety distances always select the greater distance. See "Important Safety Instructions" for further information. 27 Structural support The ceiling mounting plate will support the weight of the hood. [. . . ]