User manual THUNDER TIGER TOMAHAWH VX

[. . . ] appliance, switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally. If the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. To guarantee the electrical safety of this appliance, continuity must exist between the appliance and an effective grounding system. If there is any doubt, have the electrical system of the house checked by a qualified electrician. ~ b) Before servicing or cleaning the ~ This appliance is intended for ~ This appliance complies with current safety requirements. [. . . ] The lighting can be used independently of the fan. h On/Off button i Fan power level buttons Four fan speed selection. j Delayed Shut Down This button activates the Delayed Shut Down feature. The fan can be set to turn off automatically after either 5 or 15 minutes. 9 Operation The two sides of the hood can be operated independently of one another. Automatically switching back the intensive power level The intensive level "4" can be programmed to automatically switch back to level "3" after 10 minutes. ^ Turn the fan and the lights off. Turning on the fan ^ Press the On/Off button. The hood turns on level 2 and the indicator lights. ^ Press and hold the "Delay Shut down" button for 10 secs. ^ Press the following buttons one after another, Selecting the power level ^ Use the "­/+" controls to select the desired power level. + = increases the fan speed ­ = decreases the fan speed Levels "1" to "3" (green indicators) are usually sufficient for normal cooking. Intensive setting Level "4" (yellow indicator) should be used for a short period when frying or cooking food with a strong aroma. ­ light ­ the "­" button, and ­ the light button again. 10 Operation Fan performance The maximum air flow capacity of the dual blower system is 1250 cfm (625 x 2 cfm). Factors such as narrow duct diameter and bends will affect this value. Level 1 operates at 40% capacity Level 2 operates at 60% capacity Level 3 operates at 80% capacity Level 4 operates at 100% capacity If the power level indicators "1" and "4" flash, the automatic switch back is not activated. ^ To activate the automatic switch back press the "+" button. Do not use the pure detergent, aggressive all purpose cleaners, oven sprays, abrasive cleaning agents or limescale removers. ^ In a dishwasher: place the filter vertically in the lower basket, making sure that the spray arm is not blocked. Depending on the detergent, cleaning the grease filter in a dishwasher may cause permanent discoloration of the filter surface. ^ While the filters are removed, clean any dirt or grease from the interior casing to prevent the risk of fire. ^ When putting the grease filter back make sure that the locking clip is facing the cooking surface. ^ If the filter is incorrectly installed, insert a small screwdriver into the slit along its edge to disengage it from the casing. After cleaning and returning the grease filters the timer must be reset. ^ While the fan is on, press and hold the grease filter control until only the first "-/+" indicator is flashing. ^ The second grease filters must also be reset in the same way, even if the timer has not yet reached its maximum. 18 Cleaning and care Changing the light bulbs , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before changing the light bulbs, disconnect the hood from the power supply, see "Important Safety Instructions". Note: The appliance has 2 electrical connections, each must be disconnected from the main power supply. When in use halogen bulbs become extremely hot, and can burn your hands. Do not attempt to change the bulbs until they have had sufficient time to cool. Fingerprints or body oils deposited on the bulb will decrease its life. ^ Flip the light cover back up, making sure it clicks into place. 19 After Sales Service Repairs In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department. [. . . ] ­ If local building codes require a greater safety distance, follow their requirement. ­ If there is more than one appliance beneath the hood and they have different minimum safety distances always select the greater distance. See "Important Safety Instructions" for further information. 25 Structural support The ceiling mounting plate will support the weight of the hood. This ceiling plate must be attached to rigid structural framing that is supported in its entirety by the ceiling joists, or to the ceiling joists directly. [. . . ]