User manual THUNDER TIGER TOMAHAWK VX

[. . . ] The manufacturer cannot be held responsible for damages caused by improper use of the hood. Improper use of the appliance can lead to personal injury and material damage. READ AND SAVE THESE INSTRUCTIONS This appliance is designed to vent cooking smoke and odors only. Be certain your appliance is properly installed and grounded by a qualified technician. [. . . ] Automatic Safety Shut Off The fan will turn off automatically 10 hours after the last movement of the joystick. ^ Press the joystick once to the right to turn the fan back on again. 12 Operation Filter timers Grease filter timer A timer monitors the hours of operation. The indicator for the grease filter will light after 30 hours of fan operation. After the grease filter has been cleaned and put back in place, the grease filter timer must be reset. Checking the filter timers To check the percentage of time set already used: ^ Press the joystick to the left to turn the fan on. ^ To do this press the grease filter button for about 3 seconds. To change the hours of operation, see "Reprogramming the timers". Please program this timer, see "Operation / Reprogramming the charcoal filter timer". The charcoal filter indicator will light once the selected time has elapsed. Press it to the left for a shorter operating time, to the right for a longer operating time. ^ Press the Delayed Shut Down and charcoal filter buttons at the same time. The indicator for the charcoal filter and one of the fan power scale indicators will flash. If the procedure is not stored within 4 minutes of programming, the hood will automatically default to the "old" data. The indicators of the fan power scale show the programmed time: 1st indicator from the left = 120 hours 2nd indicator from the left= 180 hours 3rd indicator from the left = 240 hours 4th indicator from the left = infinite 15 Cleaning and care Stainless steel Before cleaning or servicing the hood, disconnect it from the power supply by either removing the fuse, unplugging it from the outlet or manually "tripping" the circuit breaker. Fingerprints or body oils deposited on the bulb will decrease the life of the bulb. ^ Remove the grease filter. ^ Turn the bulb to the left and pull it downwards. ^ Return the grease filters. ^ Loosen the bulb's fixing screw and slide it downwards. ^ Tighten the screw. 20 After Sales Service Repairs In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the phone number on the back of this booklet. ^ When contacting the Technical Service Department, please quote the model and serial number of your appliance. These are shown on the data plate which is visible when the grease filter is removed. MieleCare (only USA) MieleCare, our Extended Service Contract program, gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership. MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts. Only genuine Miele parts installed by factory trained professionals can guarantee the safety, reliability, and longevity of your Miele appliance. Please note that unless expressly approved in writing by Miele's Service department, Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele. Our goal is to prevent unauthorized (and untrained) service personnel from working on your Miele products, possibly doing further damage to them, you and/or your home. To learn more about MieleCare Extended Service Contracts, please contact your appliance dealer or visit us online at: www. store. miele. com 21 22 Installation Instructions Caring for the environment Disposal of packing material The cardboard box and packing materials protect the appliance during shipping. [. . . ] ^ DA 362-110: In recirculation mode, 2 cut outs must be made, where the ducting ends, for the installation of the recirculation vents, b. If installing the hood over an island or in a cabinet at ceiling height, a suitable cut-out has to be made in the front panel, d. ^ The exhaust connection, a, and the recirculation vent, b, are joined together with a pipe or flexible duct, c, cut to size. When installing the recirculation vents make sure that the slats point towards the center of the room and not to a wall or the ceiling. [. . . ]