User manual UNI-T DT 830E

[. . . ] Sandy Parkway Sandy, Utah 84070, USA Tel: 801-566-8800 Fax: 801-566-7005 Effective February 15, 2000 ropean Contact: Your Local Digitech Sales and Service Office or Harman Music Group 8760 S. 801-568-7638 Fax 801-568-7642 EN 60065 (1993) IEC 65 (1985) with Amendments 1, 2 & 3 EN 55013 (1990) EN 55020 (1991) Digitech Electronics 8760 S. Sandy Parkway Sandy, Utah 84070, USA Whammy All (requires a Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent. ) Warranty e at Digitech are very proud of our products and back-up each one we sell with the following warranty: 1. The warranty registration card must be mailed within ten days after purchase date to validate this warranty. Digitech warrants this product, when used solely within the U. S. , to be free from defects in materials and workmanship under normal use and service. [. . . ] Digitech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided the product is returned to Digitech WITH RETURN AUTHORIZATION, where all parts and labor will be covered up to a period of one year. A Return Authorization number may be obtained from Digitech by telephone. The company shall not be liable for any consequential damage as a result of the product's use in any circuit or assembly. Digitech reserves the right to make changes in design, or make additions to, or improvements upon this product without incurring any obligation to install the same on products previously manufactured. 6. The consumer forfeits the benefits of this warranty if the product's main assembly is opened and tampered with by anyone other than a certified Digitech technician or, if the product is used with AC voltages outside of the range suggested by the manufacturer. 7. The foregoing is in lieu of all other warranties, expressed or implied, and Digitech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall Digitech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control. OTE:The information contained in this manual is subject to change at any time without notification. Some information contained in this manual y also be inaccurate due to undocumented changes in the product or operating system since this version of the manual was completed. The ormation contained in this version of the owner's manual supersedes all previous versions. Page1 Congratulations on the purchase of your new WhammyTM Pedal. When DigiTech invented the WhammyTM pedal, it was the most revolutionary and innovative pedal to hit the guitar since the he wah wah. Nearly a decade later, in response to your demands, we have gone to painstaking engths to bring back the original WhammyTM. Every last detail was considered as we recreated his classic pitch bending effect. However, we strengthened the rugged steel chassis to endure the erils of the stage better, the addition of a MIDI input provides more flexibility, preset LEDs proide a visual indication of your selection, and the Dive Bomb setting bends your signal a full 3 ctaves down. We are proud to bring back this pedal, and we're proud that you wanted it. 3rd Up/4th Up - Bends the harmony between a third (toe up) and a fourth (toe down) above the input note. 4th Up/5th Up - Bends the harmony between a fourth (toe up) and a fifth (toe down) above the input note. 5th Up/6th Up - Bends the harmony between a fifth (toe up) and a sixth (toe down) above the input note. 4th Up/7th Up - Bends the harmony between a fourth (toe up) and a seventh (toe down) above the input note. 4th Dn/3rd Dn - Bends the harmony between a fourth (toe up) and a third (toe down) below the input note. 5th Dn/4th Dn - Bends the harmony between a fifth (toe up) and a fourth (toe down) below the input note. Oct Up/Oct Dn - Bends the harmony between one octave below (toe up) and one octave above (toe down) the input note. Harmony Presets User's Guide Page7 Detune - This group of Presets creates a copy of your input signal, slightly shifts the pitch of the opied signal and mixes it back with the original signal. As the treadle is rocked back and forth, he level of this detuned signal is changed. With the pedal in the toe up position, only the original ry signal is heard. As the pedal is rocked forward, the detuned signal is mixed with the dry gnal. The Detune Presets include: Detune Presets Shallow - The copied signal is shifted slightly out of tune from the original pitch. Deep - The copied signal is shifted substantially out of tune from the input signal. User's Guide MIDI Functions A new feature found in this incarnation of the WhammyTM is a MIDI input. MIDI messages can elect a WhammyTM Preset, engaged or disengaged the effect, and control the pedal position. [. . . ] MIDI messages can elect a WhammyTM Preset, engaged or disengaged the effect, and control the pedal position. MIDI Channel he WhammyTM MIDI channel is used for receiving incoming MIDI data only. The WhammyTM can eceive MIDI messages on any, or all MIDI channels. The following steps outline the procedure for ccessing or changing the MIDI channel: . One of the Preset LEDs will begin to flash indicating the currently selected MIDI channel. Using the reference chart below, rotate the knob to select the desired MIDI channel. [. . . ]