User manual UNIVERSAL REMOTE CONTROL UR5L-8700L SPECS SHEET

[. . . ] The Component LED light will blink twice to confirm that the code was successfully stored. *Note : If the Pre-Programmed Method did not work, or if the Code Tables do not list your Component brand, use the AutoSearch Method as explained in Section B. Now, repeat the Auto-Search Method for those Components you could not program earlier with the Pre-Programmed Method. If you can't find the right code using the Auto-Search Method, try the Learning Method in Section C. STEP3 To exit, press and hold both the [COMPONENT] and [ASPECT] buttons simultaneously until the Component LED blinks 3 times. H. Programming the System On/Off Button This allows you to program the System On/Off button so it can send up to five power On/Off commands with one button press. STEP2 Press the [SYSTEM ON/OFF] button and the [OK/SEL] button simultaneously for 3 seconds. [. . . ] STEP2 Line up the CLIKRTM-5 to the other remote, head-to-head, 1 or 2 inches apart. STEP3 Press any button on the CLIKRTM-5 that you want to teach a command to. For example, if you want to teach the [MUTE] button, press the [MUTE] button. STEP4 Press and hold the [MUTE] button on the other remote until the CLIKRTM-5 Component LED light blinks twice. *Note : The LED will blink 5 times if there was an error in the learning process. Continue learning other buttons by repeating STEPS 3 and 4. STEP5 Once you have completed teaching CLIKRTM-5 all desired commands for that Component, save the learned commands by pressing the [COMPONENT] and [ASPECT] buttons simultaneously until the Component LED blinks 3 times. Now test all the buttons to make sure they learned correctly. button simultaneously for 3 seconds. To return to original state: If you wish to restore the CBL volume control in CBL mode, repeat the above steps but press [CBL] in STEP3 . STEP1 Press the [CBL] button and the [OK/SEL] 6 Set-up Code Tables CBL-IPTV Manufacturer/Brand ADB AMINO AT&T CISCO COMCAST DIGEO MYRIO MOTOROLA MOXI NOW TV PACE SCIENTIFIC ATLANTA WEGENER TV Manufacturer/Brand BELCOR BELL&HOWELL BENQ BOXLIGHT BRADFORD BROCKWOOD BROKSONIC BYDESIGN CANDLE CAPEHART CARY AUDIO DESIGN CELEBRITY CENTURION CETRONIC CHANGHONG CITIZEN CLARION CLASSIC CLP CLASSIC COLORTYME CONCERTO CONCIERGE CONTEC CORNEA CORONADO CRAIG CROSLEY CROWN CURTIS MATHES CXC CYBERHOME DAEWOO DAYTRON DELL DIGITAL PROJECTION DIMENSIA DREAMVISION DUKANE DUMONT DURABRAND DWIN DYNASTY DYNEX EIKI ELECTROBAND ELECTROGRAPH ELECTROHOME ELEKTRA ELEMENT EMERSON TV Set-Up Code Number Manufacturer/Brand HARVARD HAVERMY HELLO KITTY HIMITSU HISENSE HITACHI HP HUMAX HYUNDAI ILO INFINITY INFOCUS INITIAL INSIGNIA INTEQ JANEIL JBL JCB JCPENNEY JENSEN JVC KAWASHO KEC KENWOOD KLEGG KLOSS KMC KNOLL SYSTEMS KONKA KREISEN KTV KURAZAI LG LITEON LODGENET LOEWE LOGIK LUXMAN LXI MAGNAVOX Set-Up Code Number Set-Up Code Number 254 255 315 249 251 313 251 313 153 254 255 253 153 314 313 251 250 K. Programming a `Macro' button. If your remote model has custom-programmable Macro buttons available, they can be programmed to act as a 'Macro' or Favorite Channel button in CABLE mode. This allows you to program up to five 2-digit channels, four 3-digit channels or three 4-digit channels that can be accessed with one button press. STEP2 Press the [MACRO] button and [OK/SEL] button simultaneously for 3 seconds. STEP3 Enter the the 2, 3 or 4-digit code for the channel you want programmed first (for example, 007) using the Number Pad, then press the [STOP] button. Then enter the code for the next channel (for example, 050), then press the [STOP] button. STEP4 Press the [CH ] button to store the channels that were selected. Press again and it will bring up the third channel. CBL-CABLE Converters Manufacturer/Brand SCIENTIFIC ATLANTA PIONEER PACE SAMSUNG MOTOROLA GENERAL INSTRUMENT HAMLIN HITACHI JERROLD MAGNAVOX MEMOREX MOXI PANASONIC PHILIPS PULSAR RCA REGAL REGENCY SKY SONY SPRUCER TOCOM TOSHIBA VIEWSTAR ZENITH Set-Up Code Number 001 003 041 042 045 046 001 103 034 051 063 076 105 001 005 002 001 030 002 111 148 005 103 104 049 050 055 103 055 005 004 103 005 003 008 009 010 069 010 012 052 111 252 044 047 006 012 013 020 085 052 047 049 050 057 230 108 047 039 040 056 052 012 015 052 060 093 100 I. Programming Channel Control You can program the channel controls (Channel Up, Channel Down, Last and Numbers) from one Component to operate in another Component mode. Default channel control settings on the remote control are as follows: CBL : CBL DVD: DVD T V : CBL AUX: AUX VCR: CBL G. AUX Function: Programming a 5 th Component You can take advantage of the AUX function to program a 5th Component such as a second TV, VCR, DVD or Audio Component. STEP1 Turn on the 5th Component you want to program (TV, VCR, DVD or Audio). STEP2 Press the [AUX] button and the [OK/SEL] button simultaneously for 3 seconds. The [AUX] Component LED will turn on for 30 seconds. [. . . ] Erasing a Single Learned Command STEP1 Press the [COMPONENT] and [ASPECT] buttons simultaneously for 3 seconds until the Component LED light turns on. STEP3 To exit, press and hold both the [COMPONENT] and [ASPECT] buttons simultaneously until the Component LED blinks 3 times. If you wish to store the TV channel control in TV mode, use the following steps. STEP1 Press the [TV] button and the [OK/SEL] button simultaneously for 3 seconds. The Component LED will blink twice to confirm the programming. TV Manufacturer/Brand A MARK ABEX ACCURIAN ADMIRAL ADVENT ADVENTURA AIKO AKAI ALBATRON ALERON AMERICA ACTION AMPRO AMSTRAD ANAM AOC APEX DIGITAL AQUAVISION ASTAR AUDIOVOX AVENTURA AVION AXION Set-Up Code Number 112 143 025 036 072 251 333 247 388 002 103 116 146 248 404 405 473 475 323 387 391 017 028 043 073 052 043 054 056 080 112 116 363 112 058 006 573 574 477 076 454 388 052 441 039 3 Operations DEFAULT STATE: Component Default: CABLE Set Top Box (STB) Channel Default: CABLE channel and numbers through the CABLE STB. [. . . ]