User manual VISONIC CLIP 4N DATASHEET

[. . . ] PROGRAMMING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4. 1 General Guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4. 2 Entering the Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . 11 4. 2. 1 Programming User Settings . . . . . . . . . . . . . . . . . . 11 4. 3 Navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4. 4 Permissions and User Codes. . . . . . . . . . . . . . . . . . . . . 12 4. 4. 1 Setting a New Installer Code. . . . . . . . . . . . . . . . . 12 4. 4. 2 Setting the Master Installer Code . . . . . . . . . 13 4. 4. 3 Setting User Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4. 4. 4 Enabling User Permit for Installer Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4. 4. 5 Configuring Permissions for System Reset after Alarm Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4. 4. 6 Configuring a Duress Code. . . . . . . . . . . . . . . . . . . 15 4. 5 Zones / Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4. 5. 1 General Guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 D-302756 4. 5. 2 Adding a Wireless Device. . . . . . . . . . . . . . . . . . . . . 25 4. 6. 1 Configuring the Length of Time the Bell is allowed to Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4. 6. 3 Configuring the Period of Strobe Light Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4. 6. 4 Enabling Siren Activation upon Telephone Line Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To Configure Event Types to be Reported to User), or press the button to take you to "<OK> TO EXIT". Enter the fourht SMS phone number (including area code, 16 digits max. ) to which pre-selected event types will be reported. 4. 8 Security System Configuration 4. 8. 1 Enable Cross Zoning Here you determine whether cross zoning will be active or inactive. Cross zoning is a method used to counteract false alarms - an alarm will not be initiated unless two adjacent zones are violated within a 30-second time limit. This feature is active only when arming AWAY and only with zone couples from zone No. You may use any one of these zone couples to create a "cross-zoned" area. Note: Every 2 crossed zones must be of the allowed zone type (Interior, Perimeter, Perimeter follower). Cross zoning is not applicable in Entry/ Exit zones and 24h zones (Fire, Emergency, 24h audible, 24h silent). 42 D-302756 or Select between "cross zone OFF" and "cross zone ON". Repeat steps 1 to 4 of section 4. 2 "Entering the Installer Menu". 14:CROSS ZONING You can now press the or menu in "DEFINE PANEL" or press the button to program any other button to take you to "<OK> TO EXIT". 4. 8. 2 Configuring Swinger Stop Here you determine the number of times each zone is allowed to initiate an alarm within a single arming/disarming period (including tamper & power failure events of detectors, PowerMaster-10, wireless siren, etc. ). If the alarms number from a specific zone exceeds the programmed number, the control panel automatically bypasses the zone to prevent recurrent siren noise and nuisance reporting to the Monitoring Station. The zone will be reactivated upon disarming, or 48 hours after having been bypassed (if the system remains armed). Repeat steps 1 to 4 of section 4. 2 "Entering the Installer Menu". 6. 05:ABORT TIME You can now press the or menu in "DEFINE PANEL" or press the button to program any other button to take you to "<OK> TO EXIT". D-302756 45 4. 8. 7 Configuring a Confirmed Alarm Here you determine that if 2 successive alarms will occur during a specific period, the second alarm will be considered as a confirmed alarm for confirmed alarm reporting, (see par. 33:CONFIRM TIME You can now press the or menu in "DEFINE PANEL" or press the button to program any other button to take you to "<OK> or Select between "disable", "30 minutes", "45 minutes", "60 minutes", and "90 minutes". Repeat steps 1 to 4 of section 4. 2 "Entering the Installer Menu". TO EXIT". 4. 8. 8 Enable Alarm upon Detection of Jammed or Missing Device Here you determine whether an alarm will be initiated (siren / report) when there is a supervision / jamming failure during AWAY arming state. When "EN standard" is selected, if there is supervision / jamming failure during AWAY arming, the siren is activated and the events are reported as tamper events. When "Other" is selected, there is no such activity during AWAY arming. 30:BELL/REP. OPT 46 D-302756 or Select between "EN standard", and "other". Repeat steps 1 to 4 of section 4. 2 "Entering the Installer Menu". You can now press the or menu in "DEFINE PANEL" or press the button to program any other button to take you to "<OK> TO EXIT". 4. 8. 9 Configuring the Jamming Detection Here you determine whether jamming (interfering transmissions, on the radio channel used by the system) will be detected and reported or not. If a jam detection option is selected, the system does not allow arming under the relevant jamming conditions. Jam Detection Options Option UL 20/20 (USA standard) EN 30/60 (Europe standard) class 6 (30/60) (British standard) Disable (default) Detection and Reporting when There is continuous 20 seconds of jamming There is an accumulated 30 seconds of jamming within 60 sec. Like EN (30/60) but the event will be reported only if the jamming duration exceeds 5 minutes. [. . . ] The Manufacturer does not represent that this Product may not be compromised and/or circumvented or that the Product will prevent any death and/or personal injury and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the Product will in all cases provide adequate warning or protection. The Product, properly installed and maintained, only reduces the risk of such events without warning and it is not a guarantee or insurance that such events will not occur. THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, OBLIGATIONS OR LIABILITIES, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE. IN NO CASE SHALL THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS WARRANTY OR ANY OTHER WARRANTIES WHATSOEVER, AS AFORESAID. [. . . ]