User manual VISONIC NEXT DATASHEET

[. . . ] EN 301489, EN 50130-4, EN 60950, EN 50131-2-2 USA: CFR47 Part 15 Canada: RSS 210 PHYSICAL Size (H x W x D): 94. 5 x 63. 5 x 53. 0 mm (3-11/16 x 2-1/2 x 21/16"). Patents 5, 693, 943 6, 211, 522 D445, 709 (another patent pending) A 5m 16. 4ft 0 5m 16. 4ft 10m 32. 8ft 0 5 16. 4 10 32. 8 15 m 49. 2 ft 2. 1 m (6. 9 ft) B C 0 5 16. 4 10 32. 8 15 m 49. 2 ft A. Coverage Pattern & Walk-test Pet Immunity (Next-K9 PG2 only): Up to 38 kg (85 lb). ELECTRICAL Internal Battery: 3V Lithium battery, type CR-123A or equivalent. [. . . ] Dispose of used battery according to the manufacturer's instructions. Nominal Battery Capacity: 1450 mA/h Battery Life (for typical use): 6 years FUNCTIONAL True Motion Event Verification: 2 remote selections - 1 (OFF) or 2 (ON) motion events Alarm Period: 2 seconds D-302413 1 3. ENROLLMENT Refer to the PowerMaster-10 Installer Guide for the device enrollment procedure. 4. MODIFY DEVICE SETTINGS This section describes how to configure the parameters of the PIR detector from the PowerMaster-10 control panel To Modify the PIR Detector Device Settings Refer to the PowerMaster-10 Installer Guide and perform the procedure for Adding A Wireless Device (section 4. 5. 2), or, Modifying a Device (section 4. 5. 5). or Select between "NOT Active", "YES ­ no delay", "YES + 5s delay", "YES + 15s delay", "YES + 30s delay", "YES + 1m delay", "YES + 2m delay", "YES + 5m delay", "YES + 10m delay", "YES + 20m delay" and "YES + 60m delay". or Select between "LOW sensitive" and "HIGH sensitive". Here you determine whether an alarm will be activated upon continued motion (low sensitivity) or upon a single alarm event (high sensitivity). Here you determine whether or not the alarm LED indication will be activated. 12. DISARM Activity When exiting "ZONES / DEVICES" menu, the PowerMaster-10 system displays the number of devices that need to be updated, as follows: DEV UPDATING NNN. For detailed instructions on Adding Devices, Deleting Devices, Replacing Devices and Defining Defaults see the PowerMaster-10 Installer Guide. 5. Put back the cover to return the tamper switch to its normal (undisturbed) position, and then secure the front cover to the base with the case closure screw. IN NO CASE SHALL THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS WARRANTY OR ANY OTHER WARRANTIES WHATSOEVER, AS AFORESAID. THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE, INCLUDING LOSS OF USE, PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR INDIRECTLY ARISING FROM PURCHASER'S USE OR INABILITY TO USE THE PRODUCT, OR FOR LOSS OR DESTRUCTION OF OTHER PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF MANUFACTURER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY INJURY AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT FAILED TO FUNCTION. ­ Re-orient or re-locate the receiving antenna. ­ Connect the device to an outlet on a circuit different from the one that supplies power to the receiver. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage arising under this limited warranty, THE MANUFACTURER'S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, which shall be fixed as liquidated damages and not as a penalty, and shall be the complete and exclusive remedy against the Manufacturer. When accepting the delivery of the Product, the Purchaser agrees to the said conditions of sale and warranty and he recognizes having been informed of. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so these limitations may not apply under certain circumstances. The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or malfunctioning of any telecommunication or electronic equipment or any programs. The Manufacturers obligations under this Warranty are limited solely to repair and/or replace at the Manufacturer's discretion any Product or part thereof that may prove defective. Any repair and/or replacement shall not extend the original Warranty period. The Manufacturer shall not be responsible for dismantling and/or reinstallation costs. [. . . ] The Manufacturer shall not be responsible for dismantling and/or reinstallation costs. To exercise this Warranty the Product must be returned to the Manufacturer freight pre-paid and insured. All freight and insurance costs are the responsibility of the Purchaser and are not included in this Warranty. This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any person to act on its behalf in the modification, variation or extension of this warranty. [. . . ]