User manual VISONIC NEXT CAM-K9 PG2

[. . . ] 10-15 images total (can be customized by request) · Works with repeaters for extended range A. SPECIFICATIONS GENERAL Detector Type: Dual element low-noise pyroelectric sensor Lens Data: No. Coverage: 12 x 12 m, (40 x 40 ft) / 90° Pet Immunity (Next CAM-K9 PG2 only): Up to 38 kg (85 lb). ELECTRICAL Internal Battery: 6V Lithium battery (two CR-123A 3V batteries or two CR17450 3V batteries, in series) or equivalent. [. . . ] or Select between "NOT connected" and "Connected to AC". Here you determine whether or not to report power failure and restore. D-302893 3 5. Put back the cover to return the tamper switch to its normal (undisturbed) position, and then secure the front cover to the base with the case closure screw. Walk across the far end of coverage pattern in both directions, The red LED lights each time your motion is detected followed by 3 LED blinks. LED response Green LED blinks Orange LED blinks Red LED blinks No blinks Reception Strong Good Poor No communication IMPORTANT!If you receive a "poor" signal from the detector, relocate it and re-test until a "good" or "strong" signal strength is received. Note: For detailed Diagnostics Test instructions refer to the control panel Installer Guide. A A. Mount on solid stable surface. 1 2 3 4 5 6 WARNING!To comply with FCC RF exposure compliance requirements, the PIR detector should be located at a distance of at least 20 cm from all persons during normal operation. The antennas used for this product must not be co-located or operated in conjunction with any other antenna or transmitter 7 Figure 4. The Next CAM-K9 PG2 detector is immune to 38 kg (85 lb) animals moving on the floor or climbing on furniture as long as the activity takes place below 1 m (3 ft). Above the 1 m (3 ft) height limit, the detector is immune to 19 kg (42 lb) pets, but the pet immunity will decrease as the pet gets closer to the detector. It is therefore recommended to select a mounting location that minimizes potential close proximity of animals. 6. 2 Mounting 2 3 1 A 4 D-302893 B 5 4 6 C 7 F D G E *CAUTION! THE BACK TAMPER SWITCH WILL NOT PROTECT THE UNIT UNLESS THE BREAK-AWAY BASE SEGMENT IS SECURED TO THE WALL WITH AT LEAST ONE SCREW. Position the battery in the battery holder and insert the battery connector terminal into the battery connector. For optional mains power supply: Break the cable entry knockout and insert the mains cable. Press the base against the wall at the selected mounting position and mark the drilling points through the mounting holes. Drill 2 holes or 3 holes (for back tamper) and attach the base to the wall using the screws. THE BACK TAMPER SWITCH WILL NOT PROTECT THE UNIT UNLESS THE BREAK-AWAY BASE SEGMENT IS SECURED TO THE WALL WITH AT LEAST ONE SCREW. SPECIAL COMMENTS Even the most sophisticated detectors can sometimes be defeated or may fail to warn due to: DC power failure / improper connection, malicious masking of the lens, tampering with the optical system, decreased sensitivity in ambient temperatures close to that of the human body and unexpected failure of a component part. The above list includes the most common reasons for failure to detect intrusion, but is by no means comprehensive. It is therefore recommended that the detector and the entire alarm system be checked weekly, to ensure proper performance. [. . . ] Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. . Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired operation. W. E. E. E. Product Recycling Declaration For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not returning it for repair then you must ensure that it is returned as identified by your supplier. [. . . ]