User manual VISONIC POWERMAXCOMPLETE PANEL QUICK GUIDE

[. . . ] Locate the magnet on the spacer at the correct direction and push it upward. 2 1 Release screw and remove cover 4 Mounting Note It is highly recommended to attach the transmitter to the top of the door/window on the fixed frame and the magnet to the movable part (door or window). Make sure that the magnet is located not more than 6 mm (0. 25 in. ) from the transmitter's marked side. Fig. Mount on solid stable surface Pressing both AWAY + HOME initiates a PANIC alarm. DISARM AWAY HOME AUX 4 D-302887 7. [. . . ] DEFINE PANEL 01: ENTRY DELAY 1 03: EXIT DELAY EXIT DELAY 60 S * 03: EXIT DELAY 10. 8) Press Press Press Select delay with and press 3 times Resultant Display 4. DEFINE PANEL 01: ENTRY DELAY 1 Entry dly1 30 s * 01: ENTRY DELAY 1 02: ENTRY DELAY 2 Entry dly2 60 s ** 6. 8. Press Press Select delay with and press 02: ENTRY DELAY 2 * The default ENTRY DELAY 1 time is 30 S. SETUP FOR GPRS/BB ­ NO PHONE LINE (STEP 1) DO NOT make any program changes in "DEFINE COM" other than those shown on this instructions unless necessary. Before continuing, remove power (AC and battery) and install a SIM card provisioned for GPRS data service. Request a SIM card phone number from your SIM supplier if you wish to have the ability to ARM / DISARM via text messaging or program from the central station receiver. Action(s) 1. 9. Press Press 3 times once Resultant Display INSTALLER MODE ENTER CODE 1. 1:PSTN/GSM 2:GPRS/BB GPRS REPORT disable enable GPRS REPORT GPRS APN Enter installer code (9999 by default) Press Press Press Press Press Press 4 times once once once once once twice 3 times once 10. Enter Access Point Name airnet1 Example: Seaguard SIM = airnet1 (Key #8 = scroll symbols up, Key #2 = scroll symbols down) (Key #5 = Toggle Uppercase / Lowercase) 14. Press twice once once GPRS APN <OK> TO EXIT READY 12:00PM D-302887 7 12. 9. Press Press 3 times once Resultant Display INSTALLER MODE ENTER CODE 1. REPORTING REPORT EVENTS 1ST RPRT METHOD disable cellular cellular 1ST RPRT METHOD IP RCVR 1 000. 000. 000. 000 069. 074. 192. 027 IP RCVR 1 IP RCVR 2 000. 000. 000. 000 208. 017. 225. 027 IP RCVR 2 LINE FAIL REPORT PSTN 5 minutes don't report don't report PSTN <OK> TO EXIT READY 12:00PM D-302887 Enter installer code (9999 by default) Press Press Press Press Press Press 4 times once twice once once once once once once 8 times once 10. Press Address twice once once Example: S&W Primary IP Address (069. 074. 192. 027) 19. Press 8 twice 9 times once once 4 times once once once once Example: S&W Backup IP Address (208. 017. 225. 027) 13. SETTING USER CODES You can program a security code for yourself and additional 7 codes for other system users. Action(s) 1. 9. Press Press Enter master user code (1111 by default) Press Press Press (The user code is 1111 by default) Enter 4 digit code e. g. 6854 Press Press 4 times 2 times Resultant Display USER SETTINGS ENTER CODE SET BYPASS SET USER CODES USER CODE 1 USER CODE 1 1 1 1 1 USER CODE 1 6 8 5 4 USER CODE 1 6 8 5 4 USER CODE 2 USER CODE 2 USER CODE 2 0 0 0 0 USER CODE 2 2 3 5 1 ACCESS TO PART U02: P1 U02: P1 P2 P2 P3 P3 Entering user settings menu 10. [. . . ] 8) Press Press Press Walk test the entire protected site to trigger all the sensors. If you get a "POOR" display from a certain sensor, relocate it and re-test until the result is "GOOD" or "STRONG". TESTING FRONT DOOR Alternately Z1 STRONG BACK DOOR Alternately Z2 GOOD 10 D-302887 16. [. . . ]