User manual VISONIC TOWER 20 AM MCW INSTALLATION

[. . . ] White Light Immunity: Above 25000 lux PHYSICAL Dimensions (height x length x width: 157x147x124mm (6-3/16 x 513/16 x 4-7/8"). Weight: 600g (21 oz) Color: white or gray STANDARDS COMPLIANCE Europe 868. 95, 433. 92 MHz: EN 50130-4, EN 60950, EN 300220, EN 301489, EN 50130-5. Canada: RSS-210 This device complies with Part 15 of the FCC Rules and RSS-210 of Industry and Science Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. [. . . ] The LED will flash for 60 seconds and then the detector will enter into 15 minutes walk-test mode. Note: The detector automatically enters into 15 minutes walk-test mode after battery installation or Tamper switch recovery. Adjust the detector in the horizontal plane to cover the required protected area. (Figure 3) It is recommended to perform the first batteries insertion on a desk. Upon battery insertion, the LED will flash for 60 seconds and then the detector will enter into 15 minutes walk-test mode. Enroll the detectors into the alarm system's memory as described in the alarm system installer guide ­ ENROLLING section. Adjust the vertical adjustment to receive the maximum number of detections when crossing the entire 90° pattern. Verify that each time your motion is detected the LED lights for 2 seconds and the control panel receives the alarm. If required, perform detector's horizontal / vertical readjustments. Instruct the user to perform walk test at least once a week, to verify proper operation of the detector. Place a piece of cardboard on the detector's front side, to deliberately mask the optical window. After 2 minutes, the LED should flash (see Table 3 below) and the alarm control panel should receive the masking alarm. The LED should extinguish or flash after about 30 sec (see Table 3). Table 3 - LED operation Event LED Operation First 60 sec after battery fast flashing insertion, or closing the detector cover Test mode (15 min. ) Normal mode (*) Mask detection fast flashing fast flashing 5 sec. ON after PIR detection first detection(**) Notes: * LED ON/OFF control by DIP switch #1 (see par. ** After detection, the detector disables itself to save battery power. It reverts to the ready state if there is no subsequent detection throughout the following 2-minute period. 3. 6 Cover Closure (see Fig. 5, steps 7-10) Tamper switch 1 2 3 4 Press firmly to release the bracket 3 screws A 5 6 7 Figure 3 ­ Battery Insertion 8 B Mark Drill 1 2 For wall Tamper switch Fasten Note The 2 screw holes enable adjustment of the bracket on the wall, if needed as a result of the walk test. 3 (3 long screws) 4 (2 short screws) Figure 4 - Installation 2 D-301620 HORIZONTAL ADJUSTMENT (-45° to +45°) Adjust 1 Release locking 2 3 Lock VERTICAL ADJUSTMENT (0° to -10° in 2. 5° clicks / steps) Adjust 4 Release locking 5 Vertical angle steps 5 3 1 6 4 2 Lock COVER CLOSURE 8 7 Turn cover 9 Cover closure Push slider 10 Figure 5 - Adjustment and Cover Closure D-301620 3 The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. WARRANTY Visonic Limited (the "Manufacturer") warrants this product only (the "Product") to the original purchaser only (the "Purchaser") against defective workmanship and materials under normal use of the Product for a period of twelve (12) months from the date of shipment by the Manufacturer. This Warranty is absolutely conditional upon the Product having been properly installed, maintained and operated under conditions of normal use in accordance with the Manufacturers recommended installation and operation instructions. Products which have become defective for any other reason, according to the Manufacturers discretion, such as improper installation, failure to follow recommended installation and operational instructions, neglect, willful damage, misuse or vandalism, accidental damage, alteration or tampering, or repair by anyone other than the manufacturer, are not covered by this Warranty. The Manufacturer does not represent that this Product may not be compromised and/or circumvented or that the Product will prevent any death and/or personal injury and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the Product will in all cases provide adequate warning or protection. [. . . ] The Manufacturer shall not be responsible for dismantling and/or reinstallation costs. To exercise this Warranty the Product must be returned to the Manufacturer freight pre-paid and insured. All freight and insurance costs are the responsibility of the Purchaser and are not included in this Warranty. This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any person to act on its behalf in the modification, variation or extension of this warranty. [. . . ]