User manual WEIDER 8507

[. . . ] WESY85070 Serial No. Write the serial number in the space above for future reference. Serial Number Decal (Under Seat) QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if there are missing or damaged parts, we will guarantee complete satisfaction through direct assistance from our factory. TO AVOID UNNECESSARY DELAYS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER HOT LINE. The trained technicians on our customer hot line will provide immediate assistance, free of charge to you. [. . . ] Press a 1 Round Inner Cap (49) into the indicated end of a 7 Handle (47). Attach the Handle with a 5/16 x 2 1/4 Bolt (33), two 5/16 Flat Washers (8), a 1/2 x 3/8 Spacer (51) and a 5/16 Nylon Locknut (3). Attach a Large U Bracket (56) to one of the Arms (46) with a 3/8 x 2 3/4 Bolt (70), 3/8 Flat Washer (9), and 3/8 Nylon Locknut (21). Attach a Large U Bracket (56) to the other Arm (46) in the same manner. 14 58 21 56 21 46 9 56 9 70 46 70 15. IMPORTANT: As you assemble the Long Cable (66) and the Short Cable (23), refer to the CABLE DIAGRAMS on page 22 of this manual to make sure that the Cables are properly routed. Insert that end of the Long Cable up through the indicated opening in the Top Frame (67). Attach the Pulley inside the Top Frame (67) with a 3/8 x 2 3/4 Bolt (70), two 3/8 Flat Washers (9), the two 1/2 x 1/2 Spacers (65), and a 3/8 Nylon Locknut (21). 15 81 65 21 9 70 9 67 66 23 9 16. Remove the 3/8 x 1 3/4 Bolt (48), 3/8 Nylon Jam Nut (5), and 3 1/2 Pulley (15) from the indicated bracket on the Top Frame (67). Insert the end of the Long Cable (66) through the bracket and down through the indicated hole. Re-attach the 3 1/2 Pulley (15) to the bracket on the Top Frame (67) with the 3/8 x 1 3/4 Bolt (48) and 3/8 Nylon Jam Nut (5). Be sure that the Long Cable is between the Pulley and the top of the bracket. 16 67 Hole 5 15 66 48 17. Attach the Pulley and a Large Cable Trap (82) to the welded bracket on the Top Frame (67) with a 3/8 x 2 1/4 Bolt (50) and 3/8 Nylon Jam Nut (5). Attach the 5/16 x 3 1/2 Bolt (87), two 5/16 Flat Washers (8), the 1 Metal Spacer (22), and a 5/16 Nylon Locknut (3) to the Front Upright as shown. Attach the Pulley to the Front Upright (42) with a 3/8 x 3 1/2 Bolt (16), a 3/8 Washer (9), and a 3/8 Nylon Jam Nut (5). Be sure that the Short Cable is between the Pulley and the Metal Spacer. 23 16 15 42 87 8 9 5 3 8 23 22 24. Attach the Backrest (41) to the Front Upright (42) with two 1/4 x 2 1/2 Screws (43) and 1/4 Flat Washers (10). 24 43 10 41 42 25. Insert the 1/4 x 2 Carriage Bolt (38) into the center hole in the Seat Plate (37). Attach the Seat Plate to the Seat (13) with two 1/4 x 3/4 Screws (18). Insert the 1/4 x 2 Carriage Bolt (38) into the indicated hole in the Seat Frame (36). Tighten a 1/4 Nylon Locknut (7) with a 1/4 Flat Washer (10) onto the Carriage Bolt. Attach the other end of the Seat (13) to the Seat Frame (36) with a 1/4 Flat Washer (10) and the 1/4 x 2 Screw (20). 25 13 37 38 18 32 10 20 7 36 13 26. Attach the 5/16 x 2 Eyebolt (62) to the Leg Lever (29) with a 5/16 Flat Washer (8) and a 5/16 Nylon Locknut (3). [. . . ] Locate the adjustment sleeve and adjustment screw near the lower end of the Short Cable (23). Slide the adjustment sleeve and the ball against the indicated 3 1/2 Pulley (15). Make sure that the cables are not too tight, or the top weight will be lifted off the weight stack. Ball Adjustment Screw Adjustment Sleeve 23 19 PART LISTModel No. [. . . ]