User manual WEIDER 8920
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WEIDER 8920. We hope that this WEIDER 8920 user guide will be useful to you.
Manual abstract: user guide WEIDER 8920
Detailed instructions for use are in the User's Guide.
[. . . ] 831. 159710 Serial No.
(Write the serial number in the space above for reference. )
USER'S MANUAL
Serial Number Decal (under seat)
SEARS, ROEBUCK AND CO. HOFFMAN ESTATES, IL 60179
CAUTION
Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference.
Visit our website at www. weiderfitness. com
new products, prizes, fitness tips, and much more!
TABLE OF CONTENTS
FULL 90-DAY WARRANTY . . Back Cover Note: A PART IDENTIFICATION CHART is attached in the center of this manual. [. . . ] During steps 9 through 22, refer to the CABLE DIAGRAM on page 19 of this manual to verify proper cable routing. Before beginning this section, identify the Short Cable (23) and the Long Cable (58) by comparing the lengths and the ends of the cables. IMPORTANT: While assembling the cables, do not overtighten the bolts and nuts securing the pulleys. Using a 3/8" x 3 1/2" Bolt (16) and a 3/8" Nylon Jamnut (25), attach the 3 1/2" Pulley (15) in the indicated location on the Top Frame (55). Be sure that the end of the Cable with the ball is on the indicated side of the Pulley and that the Cable is between the Pulley and the hook on the Top Frame (55).
9 25 15 55 58
CABLE ASSEMBLY
Ball Hook
16
10. Using a 3/8" x 1 3/4" Bolt (71) and a 3/8" Nylon Locknut (21), secure the Pulley to the indicated bracket on the Top Frame (55). Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly. Attach the Long Cable (58) to the Weight Carriage (19) with a 3/8" x 3/4" Bolt (69) and a 3/8" Nylon Locknut (21). Make sure that the Bolt and the Nylon Locknut are tight.
16
58 21
19
69
CABLE ASSEMBLY
17. Using a 3/8" x 3 1/2" Bolt (16), a 3/8" Flat 17 Washer (9), and a 3/8" Nylon Locknut (21), secure a 3 1/2" Pulley (15) and a Cable Trap (66) to the upper hole in the Press Frame (17). Hold a 3 1/2" Pulley (15) inside the indicated bracket on the Press Frame (17). Using a 3/8" x 8" Bolt (59), two 3/8" Flat Washers (9), and a 3/8" Nylon Locknut, attach the 3 1/2" Pulley to the Press Frame as shown.
15 66 16 59 9 15 21 9 17
Bracket 18. Be sure that the end of the Cable with the ball is between the Pulley and the crossbar on the Press Frame (17).
18 17 15 Ball Crossbar 23
10
19. Slide a Cable Trap (66) and a 3 1/2" Pulley (15) onto each 3/8" x 3 3/4" Bolt (68). Insert the Bolts into the Front Upright (42) from the direction shown. Hand tighten a 3/8" Nylon Locknut (21) with a 3/8" Flat Washer (9) onto each Bolt. Do not tighten the Nylon Locknuts yet.
19 42 15 9
66 68
15 21
20. Route the Short Cable (23) around the 3 1/2" Pulley (15) attached to the lower hole in the Front Upright (42). Be sure that the Cable Trap (66) is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown. Tighten the 3/8" Nylon Locknut (21) and the 3/8" x 3 3/4" Bolt (68).
20 42 15 21 23
42 15 68 66 23 Inset shows view from other side
CABLE ASSEMBLY
21. Route the Short Cable (23) up around the 3 1/2" Pulley (15) attached to the upper hole in the Press Frame (17). Be sure that the Cable Trap (66) is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown. [. . . ] Note: The actual resistance at each station may vary due to friction between the cables, pulleys, and weight carriage.
WEIGHT ON WEIGHT CARRIAGE 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125
PRESS ARM (lbs. ) 12 22 31 40 50 59 68 78 87 97 106 115 125 134 144 153 162 172 181 190 200 210 219 228 237 247
BUTTERFLY ARM (lbs. ) 7 11 15 20 24 29 33 38 42 47 51 56 60 64 69 73 78 82 87 91 96 100 104 109 113 118
LOW PULLEY/ LEG LEVER (lbs. ) 10 18 25 32 39 46 53 61 68 75 82 89 96 103 111 118 125 132 139 146 153 160 168 175 182 189
HIGH PULLEY (lbs. ) 10 16 21 26 32 37 42 47 53 58 63 68 74 79 84 89 95 100 105 110 116 121 126 131 137 142
17
TROUBLE-SHOOTING AND MAINTENANCE
Inspect and tighten all parts each time you use the home gym. The home gym can be cleaned using a damp cloth and mild non-abrasive detergent. TIGHTENING THE CABLES Woven cable, the type of cable used on the home gym, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE WEIDER 8920
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WEIDER 8920 will begin.