User manual WHIRLPOOL ADP 4119 WH INSTRUCTION FOR USE

[. . . ] €¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦ • Items not suitable for dishwashing ………………………………………… 34 34 34 35 36 Installing the machine …………………………………………………………. 36 36 36 37 37 38 38 40 Preparing the machine for use ………………………………………………… • The importance of water decalcification …………………………………. €¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦â€¦ • Filling with rinse aid and making the setting………………………………. 55 30 1 2 12 3 13 Active drying unit: This system provides better drying performance for your dishes. [. . . ] This way, overflowing salt gets immediately cleaned up through the wash operation. If you are not going to wash any dishes immediately after putting salt, then run a short washing program with an empty machine in order to avoid any damage ( to prevent corrosion )to your machine due to the salt overflow while filling in the salt container. 40 Testing strip The washing effectiveness of your machine depends on the softness of the tap water. For this reason, your machine is equipped with a system that reduces the hardness in mains water supply. The washing effectiveness will increase when the system is correctly set. To find out the water hardness level of water in your area, contact your local water board or determine water hardness level by using the test strip(if available). Make your machine’s water hardness setting according to the result obtained through the testing strip. If the hardness of the water you use is above 90 dF (French hardness) or if you are using well water; you are recommended to use filter and water refinement devices. NOTE: Hardness level is adjusted to level 3 as a factory settin Adjust the water softener according to how hard your tap water is. 41 3 1 2 4 1 Move the programme selector knob to the 0 (Reset) position while your machine is not in operation. 1 After resetting your machine, press the Start/Pause button and keep it pressed down. 2 2 Meanwhile, energise the machine by pressing the Power On/Off button. 4 4 Keep Start/Pause keys press until program monitor lights are on and off. 2 2 After the lamps “3h-6h-9h-12h” 3 have flashed, release the Start/Pause button. 4 2 Your machine displays the latest entered water hardness setting. You can adjust the levels by pressing the Start/Pause button 2 according to Table of Water Hardness Level Settings. After adjusting the water hardness level , press on/off button to save the settings in memory. 4 42 Detergent usage Use a detergent specifically designed for use in domestic dishwashers. You can find powder, gel, and tablet detergents in the market that have been designed for household dishwashers. Detergent should be put into the compartment prior to starting the machine. Keep your detergents in cool, dry places out of reach of your children. Do not fill detergent into the detergent compartment more than required; otherwise it may cause scratches on your glasses as well as lead to a poorly dissolved detergent. [. . . ] €¢ Be sure that you switched off the machine by pressing the Power On / Off button. €¢ Be sure that the water inlet filter and the machine filters are not clogged. If the control lamps won’t go out after a wash operation The Power On/Off button is released yet. If detergent residues are left in the detergent compartment Detergent has been added when the detergent compartment was wet. [. . . ]