User manual WHIRLPOOL GFE471LVS INSTALLATION

[. . . ] INSTALLATION INSTRUCTIONS 30" (76 CM) FREESTANDING ELECTRIC RANGES Table of Contents RANGE SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 INSTALLATION REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Tools and Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Location Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] A UL listed conduit connector must be provided at each end of the power supply cable (at the range and at the junction box). The wiring diagram is located on the back of the range or inside the storage drawer in a clear plastic bag. The minimum conductor sized for the copper 4-wire power cord are: 40-amp circuit 2 No. -8 conductors 1 No. -10 white neutral 1 No. -8 green grounding If connecting to a 3-wire system: Local codes may permit the use of a UL listed, 3-wire, 250-volt, 40- or 50-amp range power supply cord (pigtail). This cord contains 3 copper conductors with ring terminals or open-end spade terminals with upturned ends, terminating in a NEMA Type 10-50P plug on the supply end. Connectors on the appliance end must be provided at the point the power supply cord enters the appliance. This uses a 3-wire receptacle of NEMA Type 10-50R. 3-wire receptacle (10-50R) 5 INSTALLATION INSTRUCTIONS Unpack Range Install Anti-Tip Bracket WARNING Excessive Weight Hazard Use two or more people to move and install range. Fasten anti-tip bracket with screws provided. To mount anti-tip bracket to concrete or ceramic floor, use a ³/" (4. 8 mm) masonry drill bit to drill 2 holes at the positions marked on the bracket template. Tap plastic anchors into holes with a hammer. Depending on the thickness of your flooring, longer screws may be necessary to anchor the bracket to the subfloor. Longer screws are available from your local hardware store. Electrical Connection - U. S. A. Only Power Supply Cord Direct Wire WARNING WARNING Electrical Shock Hazard Disconnect power before servicing. Failure to follow these instructions can result in death, fire, or electrical shock. Electrical Shock Hazard Disconnect power before servicing. Failure to follow these instructions can result in death, fire, or electrical shock. 1. Remove the terminal block cover screws located on the back of the range. Remove plastic tag holding three 10-32 hex nuts from the middle post of the terminal block. A B C A. Style 1: Power supply cord strain relief Electrical Connection Options If your home has: 4-wire receptacle (NEMA type 14-50R) And you will be connecting to: A UL listed, 250-volt minimum, 40-amp, range power supply cord Go to Section: 4-wire connection: Power supply cord Remove the knockout for the power supply cord. Assemble a UL listed strain relief in the opening. 4-wire direct ³/" (1. 0 cm) A circuit breaker box or fused disconnect 4-wire connection: Direct wire A 5" (12. 7 cm) A. UL listed strain relief Tighten strain relief screw against the power supply cord. 3-wire receptacle (NEMA type 10-50R) A UL listed, 250-volt minimum, 40-amp, range power supply cord 3-wire connection: Power supply cord 3-wire direct Style 2: Direct wire strain relief ³/" (1. 0 cm) A circuit breaker box or fused disconnect 3-wire connection: Direct wire Remove the knockout as needed for the flexible conduit connection. Assemble a UL listed conduit connector in the opening. 3" (7. 6 cm) 4-wire connection: Power Supply Cord A Use this method for: New branch-circuit installations (1996 NEC) Mobile homes Recreational vehicles In an area where local codes prohibit grounding through the neutral B 1. Concuit Tighten strain relief screw against the flexible conduit. A B C A. Complete installation following instructions for your type of electrical connection: 4-wire (recommended) 3-wire (if 4-wire is not available) 2. Use a Phillips screwdriver to remove the ground-link screw from the back of the range. Save the ground-link screw and the end of the ground-link under the screw. 8 3. Feed the power supply cord through the strain relief on the cord/conduit plate on bottom of range. [. . . ] To check that the anti-tip bracket is installed, use a flashlight and look underneath the bottom of the range. Look for the anti-tip bracket securely attached to floor. Slide range back so rear range foot is under anti-tip bracket. A Level Range 1. Place level on rack and check levelness of range, first side to side; then front to back. A. If range is not level, pull range forward until rear leveling leg is removed from the anti-tip bracket. [. . . ]