User manual WHIRLPOOL OV B32 S INSTRUCTION FOR USE

[. . . ] Technical data Installation Electrical connection Environmental concerns IKEA GUARANTE 16 18 19 21 21 22 Your safety and that of others are very important This manual and the appliance itself provide important safety warnings, to be read and observed at all times. This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves and others. All safety warnings are preceded by the danger symbol and the following terms: DANGER!Indicates a hazardous situation which, if not avoided, will cause serious injury. [. . . ] When the oven is cold, dry the inside of the door with a cloth or sponge. Accessories • Soak the accessories in water with washing up detergent immediately after use, handling them with oven gloves if still hot. Cleaning the rear wall and catalytic side panels of the oven (if present): IMPORTANT: do not use corrosive or i abrasive detergents, coarse brushes, pot scourers or oven sprays which could damage the catalytic surface and ruin its self-cleaning properties. € Operate the oven empty with the forced air function at 200°C for about one hour. € Next, leave the appliance to cool down before removing any food residue with a sponge. cleaning cycle of ovens with Pyrolytic function (if present): WARNING!This function burns off spatters produced inside the oven during cooking at a temperature of approx. At this high temperature, the deposits turn into a light ash which can be easily wiped away with a damp cloth, when the oven is cool. Do not select the pyrolysis function after every use, only when the oven is very dirty or produces smoke or fumes while preheating or cooking. € If the oven is installed below a hob, make sure that all burners or electric hotplates are switched off during the self-cleaning (pyrolysis) function. -- Set the clock to (see “Control panel”) Wait 2 minutes for the door to be released. The electronic programmer does not work (Nutid and Framtid OV9 version) Electrical malfunction due to voltage fluctuations. If the electronic programmer (depending on the model) shows “F HH”, contact the nearest AfterSales Service Specify in this case the number that follows the letter “F”. Energy consumption with a standard load and pastry function Kwh ENGLISH 17 Before calling the After-Sales Service: 1. See if you can solve the problem yourself with the help of the suggestions given in the “What to do if . Switch the appliance off and back on again it to see if the fault persists. If after the above checks the fault still occurs, contact IKEA After Sales Service. Always specify: • a brief description of the fault; • the type and exact model of the oven; • the service number (number after the word Service on the rating plate), located on the right hand edge of the oven cavity (visible when the oven door is open); • your full address; • your telephone number. If any repairs are required, please contact IKEA After Sales Service (to guarantee that original spare parts will be used and repairs carried out correctly). ENGLISH 18 Technical data Dimensions Width Height Depth Usable Volumes (L) Area of largest baking sheet (net surface) cm2 Top+ bottom heating element W Grill W Defrost W Cooling Fan W Eco Function W Pyro Cleaning W Oven Lamp W Total rating W Number of functions Energy consumptions kWh Energy consumptions with a standard load and top + bottom heating kWh Energy Consumpion with a standard load and ventilated kWh The technical informations are situated in the rating plate inside the appliance. 595 595 538 59 1200 2450 2450 45 21 2450 2450 40 2500 5 0, 79 0, 79 0, 90 ENGLISH 19 After unpacking the oven, make sure that it has not been damaged during transport and that the oven door closes properly. In the event of problems, contact the dealer or your nearest After-sales Service. [. . . ] € Damage to the following parts: ceramic glass, accessories, crockery and cutlery baskets, feed and drainage pipes, seals, lamps and lamp covers, screens, knobs, casings and parts of casings. Unless such damages can be proved to have been caused by production faults. € Cases where no fault could be found during a technician’s visit. € Repairs not carried out by our appointed service providers and/or an authorized service contractual partner or where nonoriginal parts have been used. [. . . ]