User manual WHIRLPOOL UMC5200BCB-W-S 12-07

[. . . ] 3 Microwave Oven Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Duct Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Microwave Oven Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Install Top and Bottom Brackets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 4 Install Trim Kit Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 MICROWAVE OVEN SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING. " These words mean: DANGER WARNING You can be killed or seriously injured if you don't immediately follow instructions. You can be killed or seriously injured if you don't follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. W10308503A INSTALLATION INSTRUCTIONS Tools and Parts Tools Needed Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Minimum Cutout Dimensions 23³/" (60. 3 cm) 1/" (4. 0 cm) Measuring tape Pencil Phillips screwdriver Drill 7/64" drill bit Tape 16/" (42. 9 cm) 25" (63. 5 cm) htdiW A ¹¹/" Parts Supplied 3" (7. 6 cm) (1. 8 cm) B Duct base Trim kit frame A. Cutout for lower oven 1 Left duct 2 Templates 1 and 2 Bottom bracket Top bracket NOTES: Height, width and depth measurements have ±1/16" (2 mm) tolerance. 3" (7. 6 cm) minimum dimension is from lower oven cutout ceiling to microwave oven cutout floor. Trim kit frame extends 11/16" (1. 8 cm) below, and 1/" (4. 0 cm) above the cutout opening. 13/16" screws (2) 9/16" screws (16) 1/2" screws (4 - painted) Trim Kit Frame Dimensions 26/" (6 8. 3 cm)* 29³/" (7 5. 6 cm)* * Location Requirements The microwave oven may be installed over a built-in oven. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the microwave oven. Microwave Oven Installation 1. Be sure to align the center line of template to center line of cutout floor. SAVE THESE INSTRUCTIONS 14²/" (37. 5 cm) A B C A. Using 7/64" drill, drill pilot hole into hole center marked in Step 2. 3 4. Install the 3/16" screw, and leave 1/8" (3. 2 mm) to 3/16" (4. 7 mm) protruding from the cutout floor. A B ¹/" (3. 2 mm) (min) ³/" (4. 7 mm) (max) NOTE: If Template 2 is missing or unusable, measure straight up from upper end holes on bottom bracket, and mark the new holes at 12¹/" (32. 9 cm) and 15²¹/" (39. 8 cm). Make sure the bottom bracket end holes and the new holes on each side are plumb. CD TEMPLATE 2 DC DC 12¹/" (32. 9 cm) 15²¹/" (39. 8 cm) CD A. Slide microwave oven partway into cutout opening. WARNING BA AB Electrical Shock Hazard Plug into a grounded 3 prong outlet. Failure to follow these instructions can result in death, fire, or electrical shock. 6. Make sure microwave oven is centered in the opening, and slide it into place, engaging the 3/16" screw and duct base. 5. Using 7/64" drill, drill pilot holes into the cabinet through holes marked in Step 4, then remove template. [. . . ] Using 7/64" drill, drill pilot holes into the cabinet through holes marked in Step 4, then remove template. Position top bracket over pilot holes drilled in Step 5, then secure with four 9/16" screws. (Illustration in this step shows 30" [76. 2 cm] installation. ) A B C D A. Align bottom bracket to duct base, and mark 7 mounting holes of bottom bracket, as shown. [. . . ]