User manual WHIRLPOOL WED4890BQ INSTALLATION GUIDE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL WED4890BQ. We hope that this WHIRLPOOL WED4890BQ user guide will be useful to you.


WHIRLPOOL WED4890BQ INSTALLATION GUIDE: Download the complete user guide (4720 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL WED4890BQ USE & CARE GUIDE (4427 ko)
   WHIRLPOOL WED4890BQ WARRANTY INFORMATION (297 ko)

Manual abstract: user guide WHIRLPOOL WED4890BQINSTALLATION GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] ELECTRIC DRYER INSTALLATION INSTRUCTIONS 29" WIDE MODELS – U. S. A. ONLY Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su producto, visite: www. whirlpool. com Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad superior de la puerta. Table of Contents DRYER SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 INSTALLATION REQUIREMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Firmly grasp dryer body (not console panel) and gently lay dryer down on cardboard. 2. Choose electrical connection type Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to steps 1-2 on page 8 for power supply cord strain relief; then steps 3-6 for “4-wire Power Supply Cord Connection” section. Then, go to “Venting Requirements. ” Power supply cord 3-wire receptacle (NEMA Type 10-30R): Go to steps 1-2 on page 8 for power supply cord strain relief; then steps 3-5 for “3-wire Power Supply Cord Connection” section. Then go to “Venting Requirements. ” 4-wire direct connection: Go to steps 1-2 on page 10 for direct wire strain relief; then steps 3-8 for “4-wire Direct Wire Connection” section. Then go to “Venting Requirements. ” 3-wire direct connection: Go to steps 1-2 on page 10 for direct wire strain relief; then steps 3-7 for “3-wire Direct Wire Connection” section. Then go to “Venting Requirements. ” Using a wrench and tape measure, screw legs into leg holes until bottom of foot is approximately 1/2" (13 mm) (to match height of 3. 6 cu. capacity washer) or 1½" (38 mm) (to match height of 3. 8 cu. Leave enough room for electrical connection and to connect the exhaust vent. NOTE: If local codes do not permit connection of a cabinet-ground conductor to neutral wire, go to “Optional 3-wire Connection” section. Connect neutral ground  wire and neutral wire C B 3-wire Power Supply Cord Connection Use where local codes permit connecting cabinet-ground conductor to neutral wire. B A D E E C G A. 3-wire receptacle (NEMA type 10-30R) B. 3-wire plug C. Neutral prong D. Spade terminals with upturned ends E. 3/4" (19 mm) UL listed strain relief F. Ring terminals G. Neutral (white or center wire) F Connect neutral ground wire (E) and neutral wire (white or center) (C) of power supply cord under center terminal block screw (B). Remove center screw B Remove center terminal block screw (B). 9 4. Attach direct wire cable to strain relief Connect neutral wire (white or center) (C) of power supply cord to center terminal block screw (B). The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Connect remaining wires 4-wire Direct Wire Connection IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit 3-wire connections. 3. Prepare your 4-wire cable for direct connection Connect remaining wires to outer terminal block screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Now, go to “Venting Requirements. ” (25 m 1" m) Direct Wire Connection Direct wire strain relief 5 (127 " mm ) 1. Attach direct wire strain relief A Direct wire cable must have 5 ft. Strip 5" (127 mm) of outer covering from end of cable, leaving bare ground wire at 5" (127 mm). Connect wires to terminal block Unscrew the removable conduit connector (A) and any screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief through the hole (B) below the terminal block opening. Reaching inside the terminal block opening, screw the removable conduit connector onto the strain relief threads (C). To connect wires to terminal block, place hooked end of wire under terminal block screw (facing to the right), squeeze hooked end together, and tighten screw. 10 5. Connect remaining wires A B E Remove center terminal block screw (B). [. . . ] If there is an extra part, go back through steps to see what was skipped. q Check that you have all of your tools. After dryer is in place, remove corner posts and cardboard from under the dryer. q For power supply cord installation, plug into an outlet. For direct wire installation, turn on power. Level Dryer 1. See “Level Dryer. ” q Remove film on console and any tape remaining on dryer. q Wipe dryer drum interior thoroughly with a damp cloth to remove any dust. q Read “Dryer Use” in your Use and Care Guide. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WED4890BQ




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WED4890BQ will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.