User manual WHIRLPOOL WRS342FIAB WARRANTY INFORMATION
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL WRS342FIAB. We hope that this WHIRLPOOL WRS342FIAB user guide will be useful to you.
You may also download the following manuals related to this product:
WHIRLPOOL WRS342FIAB ENERGY GUIDE (403 ko)
WHIRLPOOL WRS342FIAB DIMENSION GUIDE (87 ko)
WHIRLPOOL WRS342FIAB USE & CARE GUIDE (1264 ko)
WHIRLPOOL WRS342FIAB INSTALLATION GUIDE (793 ko)
Manual abstract: user guide WHIRLPOOL WRS342FIABWARRANTY INFORMATION
Detailed instructions for use are in the User's Guide.
[. . . ] When built-in, your unit does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed and clearance is required for water and electrical connections in the rear. Note: Unit can NOT be installed behind a closed cabinet door.
Product Dimensions
17" Including Handle
24-3/4"
Cut-Out Dimensions
Filler Panel (Not Provided by U-Line) May Be Added Above or Below Unit to Enclose for a Built-In Look
13-15/16"
Figure 2
Door Swing/Clearances Information
Typical Counter Height 34-1/4" to 35-1/8" Cut-Out Height 24-7/8" to 25" 8" 14-3/16" 1/4" Min.
18-1/2" Minimum See Electrical Specifications for Power Supply
Units have a zero clearance for the door to open 90° (see Figure 3). U-Line recommends a minimum door clearance of 1/4" to accommodate the handle if the unit is right-hand hinged and installed next to a wall or similar type of structure. [. . . ] Clean out bushing hole in door bottom with a screwdriver if necessary. Remove plastic hole plug from door handle and relocate on opposite side. See Figure 9.
Bushing
Figure 8
Hinge
Plastic Plug Hole
Plastic Plug Hole
Screw Right Side Door Swing Right Side Hinge Invert Screw Invert Hinge Left Side Door Swing
Figure 4
Figure 5
3. Note that there may be a nut behind one or both screws on either side.
Figure 9 7. Remove pivot screw from top hinge, invert screw and reinstall pivot screw in top hinge. Remove three plastic screw plugs from hinge holes, top of cabinet, opposite side. Invert and install upper hinge on door.
Figure 10 Figure 6 Figure 7
4. Align hinge outer edge with cabinet before tightening screws.
02/2005
5
www. U-LineService. com
BI-95 Ice Maker
10. Replace three plastic plugs removed in Step 8 into holes on top of unit. Replace screws in holes in bottom of unit on opposite side.
4 Prepare and Install Door Panel
Units will accept a Custom 1/4" Thick Insert to harmonize with or accent the surrounding decor. If this treatment is not included in this installation, go on to 5 Adjust Door.
Custom 1/4" Thick Door Panel Insert
Figure 11
Door Panel Preparation
A custom door panel can be inserted into the doorframe. Install the 1/4 inch OD copper water line from the main water source.
2. Slide the compression fitting and ferrule over the 1/4-inch OD water supply line. Using two wrenches, tighten the compression fitting on the supply line (see Figure 16). Carefully bend the water supply line into position and connect the line to the solenoid valve (see Figure 17). Avoid kinking the water supply line.
Figure 18
IMPORTANT
Route the water supply line through the unit so it does not come into contact with any internal components other than the solenoid valve. A water supply line contacting an internal component or cabinet wall can cause excessive noise during operation or damage to the line. For recessed installations, allow extra water supply line length to provide slack for easy removal from the recessed area (see Figure 18). Go on to 7 Prepare Power Supply.
www. U-LineService. com
8
02/2005
BI-95 Ice Maker
7 Prepare Power Supply
8 Level the Unit
Electrical Specifications
CAUTION
Electrical installation must observe all state and local codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a qualified electrician. The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A power supply (normal household current). An individual, properly grounded branch circuit or circuit breaker is recommended. [. . . ] See Figure 22.
www. U-LineService. com
10
02/2005
BI-95 Ice Maker
10 Start-Up for the First Time
Start-Up Troubleshooting
Initial Start-Up
The on/off switch is located behind the front grille. A small opening in the top of the grille is provided to access the switch. For information about Adjusting the Temperature Control, see the User Manual. As soon as the ice maker mold reaches the proper temperature, the ice maker mechanism will fill the mold with water. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WRS342FIAB
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WRS342FIAB will begin.