User manual WHISTLER 3400 INSTALLATION

[. . . ] Interface Cable (3400 only) · connects the radar antenna to inside control panel Qty 2 B 2 C D E F 4 4 2 7 G 2 H 1 I 1 J 5 K 1 Note: If mounting fasteners are missing from your package, please call 1-800-531-0004 for replacements. 6 INSTALLATION OF RADAR ANTENNA General Information The radar antenna is waterproof and designed to be mounted at the front of your vehicle. In most vehicles the best mounting location is directly below or behind the bumper. Other locations which provide concealment and/or protection of the antenna such as on the rear deck (next to the third brake light) may be acceptable. Radar signals will pass through nonmetallic materials such as fiberglass and plastic, however, be sure to mount the receiver away from any metal, as it will block the receiver's antenna. [. . . ] Select the position that allows you to fasten the antenna to your vehicle in the most secure manner 9 INSTALLATION OF RADAR ANTENNA Best mounting angle for optimum detection of all types of radar guns. Horizontal Mounting Radar antenna mounted in horizontal position. When mounting the antenna in a horizontal position (or on an angle between), remember to keep the ANTENNA window as close to perpendicular as possible to the road surface (ANTENNA window should not be angled up toward the sky or down toward the road surface). Mounting Vertical (with 45º Reflector) For vehicles that do not have sufficient clearance behind the bumper (about 5") to mount the antenna in a horizontal position, the 45º. The 45º Reflector is attached to the antenna with two screws (#6 x 3/4") on the side of the antenna housing marked ANTENNA. Slide the screws through the corner holes on the flange of the antenna housing and then tighten into the metal reflector (do not over tighten). 10 INSTALLATION OF RADAR ANTENNA Mount the antenna to the vehicle such that the ANTENNA window is facing the road surface, sky, right or left of the vehicle, and the reflector has an unobstructed view of the road ahead. This side facing forward traffic Antenna window Signal Radar antenna mounted(vertical) with 45 º Re flector . Mounted in this position, radar signals are reflected into the ANTENNA window. Mounting the Temperature Probe Find a location that is far enough away from the engine and radiator heat but still in the airflow for the vehicle. Mounting the Probe too close to these heat areas will give a false high temperature. · Attach the mountable tie wrap (supplied) to the Temperature Probe as shown. · Mark location for Probe, then drill a hole using a 7/64" drill bit. Attach Probe with tie wrap in the correct orientation using the #6 x 3/4 screws. NOTE: Mount the Probe so that there is space between the Probe and the mounting area. Do not mount Probe directly to metal area. Mountable Tie Wrap Temperature Probe Probe Cable Mounting Location 11 INST ALLA TION OF LRM-5 Antenna Cable to Control Panel Once the antenna is installed (the 3400 model has a Quick Disconnect Interface Cable. Follow the remaining procedure. ), run the cable along the edge of the engine compartment to the firewall. Find a location in the firewall where other wires (or the speedometer cable) enter the passenger compartment and feed the stereo jack connection through. Be careful not to interfere with or disconnect other wires, cables, or mechanical systems of your vehicle while routing the antenna cable. Also, keep the antenna cable away from any areas in the engine compartment that may become hot. Cable ties are provided to secure the antenna and Temperature Probe cables at various points in the engine compartment. General Information The LRM-5 (Laser Receive Module) provides both front and rear laser reception. Mount the LRM-5 with the 3-lens array facing forward (down the road) and the single lens facing behind. This approach offers the greatest protection, since you will most often be traveling into a laser signal, rather that away from it when laser speed enforcement is encountered. For effective protection, make sure the LRM-5 has an unobstructed view forward and behind, and that it is not placed behind metallic sun screens. [. . . ] Before adhering the adhesive side of the fastener to a surface, clean that surface with isopropyl alcohol. Use of Hook & Loop simplifies control panel installation. Control Panel Mounted With Through Dash Bracket Installation instructions are provided with the bracket. We recommend using a professional installer if you are not familiar with customized dashboard installations. 5. Power Port 15 INST ALLA TION OF CONTROL PANEL Antenna Cable Connection The stereo connector (straight end) on the end of the antenna cable plugs into Radar 1 port (2) on the back of the control panel. PROBLEM: Unit alarms when using vehicle equipment or electrical accessories (brakes, power mirrors/windows, directionals, horn, etc. ) · Check condition of vehicle's electrical system, including battery and alternator. [. . . ]