User manual XEROX 2101ST PIKAOPAS

[. . . ] It also includes guidelines for setting up UNIX, Windows NT 4. 0/2000/2003, and Novell NetWare servers to provide printing services to users. · The Printing Guide describes the printing features of the Fiery EX2101 for Xerox 2101 for users who send jobs from their computers. · The Job Management Guide explains the functions of the job management utilities, including Command WorkStationTM, Command WorkStation LETM, and DocBuilder ProTM, and how you can use them to monitor and control jobs on the Fiery EX2101 for Xerox 2101. This manual is intended for an operator or administrator, or a user with the necessary access privileges, who monitors and manages job flow and troubleshoots problems that may arise. [. . . ] If your segment has only one zone, the Fiery EX2101 is assigned to that zone automatically. The message "No AppleTalk zone found" may mean your network has no zones, or the network cable is not connected (see Appendix A). TCP/IP Setup options Exit Protocol Setup AppleTalk Setup TCP/IP Setup IPX/SPX Setup Protocol Setup To configure the Fiery EX2101 for TCP/IP, choose TCP/IP Setup. Choose each network type you use (Ethernet) and enter the appropriate settings. When you set an IP address, subnet mask, or gateway address for the Fiery EX2101 during Setup, you can allow the Fiery EX2101 to get these addresses automatically from a DHCP or BOOTP server. Make sure the DHCP or BOOTP server is running, and then perform Fiery EX2101 Setup. 4 Network Setup Protocol Setup TCP/IP Setup 4-17 Network Setup options TCP/IP Setup with Ethernet Ethernet Setup Enable TCP/IP for Ethernet Yes/No [Yes] Select Yes if you have a TCP/IP network connected to the Fiery EX2101 over Ethernet cabling. NOTE: If you are using TCP/IP for printing from Windows computers, enabling TCP/IP here also enables you to use Fiery utilities from Windows computers using TCP/IP protocols. Enable Auto IP Configuration Yes/No [Yes] Select Yes to allow the Fiery EX2101 to obtain its Ethernet IP address by searching the network. Depending on your network and the protocol you select in the following option (DHCP or BOOTP), the IP address can change. If you select No, you proceed to the IP Address option, where you manually set the IP address. Select protocol DHCP/BOOTP [DHCP] This option appears only if you answered Yes to Enable Auto IP Configuration. Select the protocol over which the Fiery EX2101 should search for its IP address. Both DHCP and BOOTP allow the Fiery EX2101 to obtain the Ethernet IP address and Subnet Mask automatically. Press the line selection button again to cancel a selected frame type. Use the up and down arrow buttons to scroll to additional frame types. When you have selected all the frame types used, choose Exit IPX/SPX Setup. Clear Frame Types To clear all frame types at once choose Exit IPX/SPX Setup>IPX/SPX Setup>Clear Frame Types. Service Setup options PServer is a program in the Fiery EX2101 software that can service the Novell Print queues assigned to the Novell print servers you have set up for printing to the Fiery EX2101. When you choose PServer Setup and enable PServer, you can set up NDS (Novell Directory Services), Bindery Services, or both. NDS is used with NetWare; Bindery Services are used with NetWare in bindery emulation mode. 4 Network Setup Service Setup LPD Setup Network Setup Service Setup PServer Setup 4-22 Performing Setup from the Control Panel LPD Setup options Enable LPD Yes/No [Yes] Select Yes to allow lpd printing. For more information, see "Setting up the Fiery EX2101 on TCP/IP networks" on page 2-17. PServer Setup options Enable PServer Yes/No [No] Select Yes if you have a Novell network connected to the Fiery EX2101. Exit PServer Setup NDS Setup Bindery Setup Polling Interval PServer Setup Choose NDS Setup if your network uses NetWare in native mode. Choose Bindery Setup if your network uses NetWare in bindery emulation mode. If your network uses both NDS and Bindery, and uses NetWare servers in bindery emulation, note that the Fiery EX2101 cannot service NDS and bindery emulation servers on the same NDS tree. 4 Network Setup Service Setup PServer Setup 4-23 Network Setup options NDS Setup Before entering NDS settings, make sure the Fiery EX2101 is connected to the network and that you have configured an NDS directory tree with a printer, print server, and one or more Print queue objects for Fiery EX2101 jobs (see "Setting up a NetWare Print queue for bindery" on page 2-13). If access to the print server is restricted, you need a login password. The main objective of NDS Setup is to specify the print server object. [. . . ] Suggested action or exit Enable a guest account on the NetWare server for the purpose of Setup. In the ENTER LOGIN NAME screen, change the default name (guest) to supervisor or another valid login name. When you are prompted for a password, enter the correct password for the account you named. The error screen exits to the File Server Login screen (if login to file server failed) or NetWare Print Server screen (if login to Print Server failed). [. . . ]