User manual XEROX NUVERA 120MX

[. . . ] Paper stack clamp: Secures the paper stack to the paper table to maintain stack integrity during transport. Locking rear casters: Stabilize the Cart while docked with the stacker or while offloading the stack. Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide 1 Parts Overview Parts Overview 1. Hands-Off Stack Transfer (HOST): Activated with the stack transport handle to transfer the paper stack onto a work table. Alignment tine: Single yellow tine helps position the Cart for docking with the XPS Stacker. [. . . ] Keep the belts clean, dry and free from debris and dirt. 8 Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide Charging Charging Charging in the Media Cart The Media Cart battery should be charged if the battery meter is outside the green zone on the meter. Battery meter 1. Ensure that power to the Media Cart is switched off. Power switch Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide 9 Charging 2. Connect the battery charger to the battery. Connect charger here Battery charger 3. Plug the power cord into the battery charger. Battery charger Power cord 4. Charge the battery for 6-8 hours or until the light on the charger indicates that it is charged. When light turns green, battery is charged. 10 Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide Specifications Specifications Production Media Cart size Length: 43. 5 in. (364 x 660. 4 mm) Maximum stack capacity 56 gsm – 400 gsm: 270 mm 75 gsm – 2600 sheets Maximum load capacity 160 lbs. (72. 6 kg) Pickup height From XPS low: 210 mm (8. 26 inches) From XPS high: 600 mm (23. 6 inches) From iGen: 103 mm (4. 06 inches) Elevation limits Maximum unload height of stack: 920 mm (36. 2 inches) Minimum unload height of stack: 100 mm (3. 9 inches) Required kit Install the XPS Media Cart Stacking Surface Kit to enable docking with the XPS Stacker Install the iGen Pallet Interface Kit Install the iGen Powered Eject Kit Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide 11 Operating the Xerox Production Media Cart (Nuvera) Docking the Xerox Production Media Cart with the Xerox Nuvera XPS Stacker It is recommended that you first practice docking the Production Media Cart (Cart) without a paper stack loaded. Warning Do not exceed the load capacity of 160 lbs. Position the Cart in front of the XPS Stacker after it has moved out from the printer. High position Low position 12 Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide Operating the Xerox Production Media Cart (Nuvera) 2. Locate the line on the cart post that corresponds to the stacker height (low: 210 mm; high: 600 mm). Press the upper or lower part of the elevation button to raise or lower to match the short lines on the sides to the line on the cart post. Low position Line up pointer to hole High position Line up pointer to hole 3. Line up the Cart tines with the XPS tines. Low position High position 4. Align the colored tine with the arrow on the XPS Stacker. Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide 13 Operating the Xerox Production Media Cart (Nuvera) 5. Make fine adjustments to the Cart height to ensure that the tines clear the XPS Stacker and the bottom of the paper stack. Move the Cart forward slowly until the black line on the Cart’s alignment tine aligns with the black line on the XPS Stacker. 7. Press down on the lock tab on the rear casters to stabilize the Cart. The Cart is now properly docked with the XPS Stacker. 14 Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide Operating the Xerox Production Media Cart (Nuvera) Lifting the Stack from the XPS Stacker 1. Press the upper part of the elevation button to raise the height of the Cart until the bottom of the cart clears the XPS Stacker. 2. Gently lift up on the paper stack clamp near the clamp post to free it for rotation. Lift it high enough so that it will clear the top of the paper stack. Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide 15 Operating the Xerox Production Media Cart (Nuvera) 3. Gently press the clamp at the clamp post to secure it. Low position High position 5. Press the tab on the upper part of the caster lock on the rear casters to release them. 6. Guide the Cart out until it clears the stacker. 16 Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide Operating the Xerox Production Media Cart (Nuvera) Transferring the Stack to the CP Bourg BSFEx Air Table This procedure assumes pick up from the XPS low position. [. . . ] Move the Cart forward until the front of the horizontal post mates with the red docking station at the base of the Air Table. 4. Gently lift up on the paper stack clamp near the clamp post, rotate it to one side, and rest it in the locator on the clamp post. 6. Turn the stock transport handle approximately 15 turns clockwise to transfer the paper stack to the Air Table. 28 Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide Operating the Xerox Production Media Cart (Nuvera) Offloading the Stack to a Work Table This procedure assumes pick up from the XPS high position (600 mm). Press the upper part of the elevation button to raise the media table height until it exceeds the height of the work table enough for the bottom of the paper stack to clear it. 2. [. . . ]