User manual XTANT X215 TECHNICAL DATA REPORT

[. . . ] Adjustment is made by installing a jumper across the associated input voltage/pin location. Refer to the illustration on the reverse side of this document prior to setting the input sensitivity. INSTALLER DA T E INSTALLED: N A M E: ' S REFERENCE LOG xtant technologies installer's reference OWNERS PHONE: TH I S A D D R E S S: CI T Y/ ST A T E: V E H I C L E: XT A N T A M P L I F I E R: M O D E L CROSSOVER MODES OF OPERATION The 2200ix is equiped with two (2) crossover mode jumpers. [. . . ] The four (4) position header jumper controls the crossover function as it applies to the 2200ix's amplifier. The modes of operation are: Position 1 = Bypass (Full Range), Position 2 = High Pass, Position 3 = Low Pass, and Position 4 = Band Pass. (See illustration) The three (3) position jumper controls the crossover function as it applies to the RCA Line Outputs. The modes of operation are: Position 1 = Bypass (Full Range), Position 2 = High Pass, and Position 3 = Low Pass. (See illustration ) The High and Low Pass frequenies are determined by the F r e q u e n c y M o d u l e s ( S I P s ) i n s t a l l e d i n t h e t w o ( 2 ) S I P s o c kets pictured on the reverse side of this document. ZI P: YE A R: S E R I A L# DOCUMENT H A S B E E N C R A F T E D T O M A K E I N S T A L L AT I O N, SYSTEM D E S I G N A N D TROUBLE- SHOOTING, A Q U I C K A N D E A S Y PROCESS. TH E C H A R T S P R O V I D E D, O F F E R A S I MP L E METHOD O F D O C U M E N T A T I O N. CROSSOVER SETTINGS: S I P HIGH P A S S V A L U E C O D E: S I P LOW P A S S V A L U E C O D E: I N P U T S E N S I T I V I T Y J U M P E R (CIRCLE SETTING) JUMPER SETTINGS: AMPLIFIER: (CIRCLE SETTING) IT IS IMPORTANT THAT YOU RETAIN THIS LOG FOR YOUR RECORDS. ON P A G E 1 2 O F T H E OWNER'S MA N U A L, Y O U W I L L F I N D T H E OWNER'S REFERENCE LOG. ONCE Y O U H A V E N O T A T E D T H E F I N A L SETTINGS F O R T H I S 2 2 0 0I X, T R A N S F E R THOSE SETTINGS T O T H E OWNER'S REFERENCE LOG. TURN ON AMPLIFIER. Check red LED, it should be on. ADJUST LEFT, RIGHT AMPLIFIER GAINS. ADJUST NOISE GATE THRESHOLD (IF USED): SPECIAL COMPONENTS SERIAL SERIAL Turn noise gate on and adjust the threshold by turning clockwise to increase sensitivity (gate will open with less i n p u t s i g n a l ) . T h e g r e e n LED w i l l i l l u m i n a t e w h e n t h e gate passes signal. AFTER FINE TUNING THE SYSTEM: xtant technologies · · · · · · · · · 7 6 7 6 SOUTH 4 6T H STREET PHOENIX, ARIZONA 8 5 0 4 0 U S A · · · · · · · · 602. 431. 8686 Remove protective covering from amplifier and clean per the maintanence section on page 9 of the O w n e r ' s M a n u a l . Attach cover to base. · · · · · · · · · INSTALLER'S . REFERENCE. . . . . . . . . . . . . INDEPENDENT LEFT AND RIGHT AMPLIFIER GAIN FREQUENCY SELECTION: CROSSOVER CONTROLS ­ ROTATE CLOCKWISE TO INCREASE SENSITIVITY. TO CHANGE THE FREQUENCY OF EITHER THE HIGH AND/OR LOW P ASS FILTERS, REMOVE AND REPLACE THE FREQUENCY MODULE (SIP) LOCATED ON THE CIRCUIT BOARD NEXT TO THE CROSSOVER MODE JUMPERS. NOTE THAT THE IDENTITY OF THE HIGH & LOW P ASS SOCKETS ARE NOT MARKED ON THE BOARD. REFER TO THIS DRAWING FOR LOCATION & THE CHART ON THE BACK FOR THE AVAILABLE SELECTION OF SIP / FREQUENCY VALUES. right Left HIGH PASS SIP INPUT SENSITIVITY: TO ADJUST INPUT GAIN, MOVE JUMPER (IF NEEDED) ­ AND INSTALL IT IN THE LOCATION WHICH MATCHES YOUR INPUT SIGNAL LEVEL. [. . . ] REFER TO THIS DRAWING FOR LOCATION & THE CHART ON THE BACK FOR THE AVAILABLE SELECTION OF SIP / FREQUENCY VALUES. right Left HIGH PASS SIP INPUT SENSITIVITY: TO ADJUST INPUT GAIN, MOVE JUMPER (IF NEEDED) ­ AND INSTALL IT IN THE LOCATION WHICH MATCHES YOUR INPUT SIGNAL LEVEL. REFER TO THE ILLUSTRATION BELOW FOR PROPER JUMPER LOCATION / LEVEL SETTING. [. . . ]