User manual ZALMAN CNPS7000B

[. . . ] 4) 92mm fan inside the FHS maximizes airflow and makes installation easier. 5) Adjustable fan speed controller (FAM MATE 2) enables control of noise and fan performance. is not responsible for any damage resulting from CPU OVERCLOCKING. 2. [. . . ] Components 1) Common Components FHS Assembly (CNPS7000B-AlCu/Cu) Four (4) Bolts (for installing the FHS) Thermal Grease Fan Speed Controller (FAN MATE 2) Double - sided Tape (for installing FAN MATE 2) Cable for FAN MATE 2 User's Manual (in English and Korean) 2) Components for Intel Pentium 4 (Socket 478) Two (2) Clip Supports For Socket 478 3) Components for AMD Duron / Athlon / Athlon XP (Socket 462) One (1) A-Type (blue) Clip Support for Socket 462 One (1) B-Type (white) Clip Support for Socket 462 Four (4) Bolts (for fastening the Clip Supports) One (1) set of Washers 4) Components for AMD Sempron / AMD64 (Socket 754/939/940) Two (2) Nipples One (1) Backplate Big washers (from component ) 2 6. Compatible CPUs 1) Intel Pentium 4 - Socket 478 All speeds of Pentium 4 Socket 478 CPUs up to 3. 4GHz When using 3. 4GHz Northwood CPU or Prescott CPUs of 2. 8A/E GHz or faster, please refer to the following table to set the fan speed accordingly for sufficient cooling. < CNPS7000B Fan Speed Table > CPU Cooler Northwood 3. 4 Prescott 2. 8A/E, 3. 0E, 3. 2E, 3. 4E 2, 500rpm or faster 2, 200rpm or faster Fan speed of 2, 500rpm can be obtained by directly connecting 3-pin fan connector to motherboard. (Without Fan Controller) Cautions ) As shown in Figure 2, a motherboard that is not compliant with the 10. 2mm Motherboard component height restriction standard, introduced by Intel, may create interference between components and the clip. No components higher than 39mm (possible examples : PSU, graphics card, RAM, etc. ) should be present within a 55mm radius from the center of the CPU to install this product. For more information, please visit the Zalman website (http://www. zalman. co. kr) and click on Compatibility between CNPS7000(A/B) and Socket 478 Pentium 4 Motherboards link. 10. 2mm Motherboard component height restriction Clip Motherboard Component Top View Top View Clip Motherboard Component Figure 1 Compatible Side View Figure 2 Not Compatible Side View 2) AMD Duron / Athlon / Athlon XP - Socket 462 All CPUs conforming to Socket 462 platform Cautions ) This product requires Heatsink Attach Holes around the CPU socket as shown on the right. No components higher than 39mm (possible examples : PSU, graphics card, RAM, etc. ) should be present within a 55mm radius from the center of the CPU to install this product. This product cannot be installed if any motherboard component (usually capacitor) taller than 15mm is located under the clip. For more information, please visit the Zalman website (http://www. zalman. co. kr) and refer to CNPS7000(A/B) Compatible Socket 462 Motherboards List link. 3 3) AMD Sempron / AMD64 - Socket 754/939/940 All CPUs conforming to Socket 754/939/940 platform Cautions ) No components higher than 39mm (possible examples: PSU, graphics card, RAM, etc. ) should be present within a 55mm radius from the center of the CPU to install this product. For more information, please visit the Zalman website (http://www. zalman. co. kr) and refer to CNPS7000(A/B) "Compatible Socket 754/939/940 Motherboards List link. 7. Installation (Intel Pentium 4 - 478) 1) Apply Thermal Grease CPU (IHS) Clean off particles and residue and then spread the included thermal grease thinly and evenly over the CPU that touches the FHS surface. Thermal Grease 2) Install Clip Supports for Socket 478 Retention Guide Clip Support for Socket 478 Install the clip supports for socket 478 on both sides of the retention guide as shown on the right. 3) Insert Bolts Bolt Insert the two bolts into the inner holes of the clip. Inner Hole Clip 4) Place FHS Set the FHS at the center of the CPU. Screw the bolts in slightly, and then tighten them in an alternating fashion until the clip supports are completely pressed against the clip. FHS Cilp Support for Socket 478 5) Supply Power (Connect FAN MATE 2) Please refer to FAN MATE 2 Installation and Usage on page 7. 4 8. Installation (AMD Duron / Athlon / Athlon XP - 462) 1) Install Clip Supports for Socket 462 Install the clip supports for socket 462 on the motherboard. Make sure to place A-type (blue : installed near the lever) and B-type (white) supports at the appropriate location. The installation should be done in the order of : bolts > small washers > motherboard > small washers > clip supports (see below). Clip Support B for Socket 462 (White) Clip Support A for Socket 462 (Blue) Lever Small Washer Motherboard Small Washer Bolt Clip Support B for Socket 462 (White) 2) Apply Thermal Grease Clean off particles and residue and then spread the included thermal grease thinly and evenly over the CPU core that touches the FHS surface. CPU Thermal Grease 3) Insert Bolts Insert the two bolts into the inner holes of the clip. Bolt Inner Hole Clip 4) Place FHS Set the FHS at the center of the CPU. Screw the bolts in slightly, and then tighten them in an alternating fashion until the clip supports are completely pressed against the clip. FHS Cilp Support for Socket 462 5) Supply Power (Connect FAN MATE 2) Please refer to FAN MATE 2 Installation and Usage on page 7. 5 9. [. . . ] If this happens, turn the speed control knob fully clockwise to increase the fan speed. Then set `CPU Fan Detected' to `Disabled' in the BIOS settings, or set the slowest rotational speed of the CPU fan in the system monitoring program to less than or equal to 1, 300rpm. Note) Some motherboards do not boot if the rotational speed of the CPU fan is below a certain rpm. For more information on updating your BIOS, please refer to your motherboard manufacturer's website. [. . . ]