User manual ZALMAN GWB3

[. . . ] (English version) ZM-GWB3 VGA WATER BLOCK for Higher Water Cooling Performance Please visit our website and watch the ZM-GWB3 installation video for easy installation. The specifications of this product and its components may change without prior notice to mprove performance. http://www. zalman. co. kr http://www. zalmanusa. com Precautions 1) Test the product for leakage away from the system before installing it on the system. 2) Use approved coolant for computer water-cooling to prevent corrosion. [. . . ] Exploded View Bolt GWB3 Ass'y Nipple Rubber Ring Washer Plate Spring Nut 3 5. Installation Procedure 1) Install Nipples and Fixing Nuts Insert the Nipples and Rubber Rings into the front side of the VGA card, then install the Washer Plate (PVC), Springs, and Fixing Nuts in the mentioned order. Note 1) Screw the Fixing Nuts only to a point so that the Fixing Nuts stay connected to the Nipples (approximately two screw turns). Nipple Nut Spring Washer Plate 2) Thermal Grease Applycation Clean the contact surface of the VGA Chipset completely. Apply Thermal Grease on the VGA Chipset that makes contact with the base of theVGA Cooler. Spring Fixing Nut Thermal Grease 4 3) Installing the VGA Water Block Place the VGA Water Block and the clip on the center of the VGA chipset. Screw each bolt B on each nipple slightly, and tighten each bolt a few turns at a time while alternating between the two until the bolt ends are completely pressed against the Nipples. Note 1) Nipples and Fixing Nuts are not completely fixed on to each other, therefore hold the Nipple with one hand while screwing in the Bolts. Bolt Nipple 4) Control Tension between VGA Water Block and VGA Chipset Tighten/loosen the Fixing Nuts on the back side of the VGA card in order to control the tension between the VGA water block and VGA chipset. Note 1) If the Fixing Nuts are turned too tightly, then damage to the VGA chipset or VGA card could occur. Note 2) Fully tightening one Fixing Nut at a time may result in damaging the VGA chipset. Please tighten each Fixing Nut one rotation at a time until all are completely tightened. Note3) Make sure that the VGA Cooler does not interfere with the VGA card's capacitors and other components. Nut Washer Plate Spring 5 5) VGA Card Installation Insert the assembled VGA card into the motherboard's PCIe (or AGP) slot. If the VGA card has a power connector on it, remember to plug in th power cable. Fixing Bolt 6) Installing the Tubes and the Tube Clamps Plug the tubes over the VGA Water Block'sfittings and install the Tube Clamps. Tube Tube Clamp To install RWB1 (Optional) 1) Remove the film from the thermal tapes on the bottom of theRAM Heatsinks and attach the heatsinks on the VGA RAM. [. . . ] Note 3) Cutting the tubes to adequate length before-hand will simplify the process of connecting tubes to the VGA water block and RWB1 INLET OUTLETT 7 Zalman Noise Prevention System Stable performance and noiseless liquid cooling system can both be achieved with the use of Zalman's Noiseless Power Supply, HeatPipe Hard Disk cooler, Noiseless Case Fan and Northbridge Water Block. Noiseless Power Supply Heatpipe HDD Cooler Noiseless Case Fan Northbridge Water Block TNN(Totally No Noise) Computer Case TNN 300 TNN 500AF NN Computer Enclosures are the world's first environment-friendly noiseless computer enclosures that operate without the use of a fan. TNN Computer Enclosures use the aluminum enclosure itself as a heatsink. They are ideal for environments that require silence, as well as for home theatre systems and multi-media systems. TNN(Totally No Noise) Computer Case The HD160 is designed for ultra quiet home theatre PC operation, utilizing optimized ventilation and anti-vibration reinforcements, making it ideal for environments that require silence such as living rooms, bedrooms, educational facilities, and offices. HD160 For more information, please visit our website. 8 [. . . ]