User manual ZENITH H20D50DT OPERATING GUIDE

[. . . ] Installation and Operating Guide | Warranty Model Number | H20D50DT | HealthView TM TV table of contents page 5 © Copyright 2001, Zenith Electronics Corporation RECORD THE MODEL NUMBER For Customer Support/Service please call: 1-888-865-3026 www. zenith. com The model and serial number of this HealthViewTM TV are located on the back of the cabinet. For future reference, we suggest that you record these numbers here: MODEL NO. ____________________________________ SERIAL NO. ____________________________________ WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. [. . . ] Remember, you can "blank" a channel for accommodating audio-only, such as an FM radio station or in-house communication. You may leave any unused bank with the channels entered during Auto Program; or, you may delete the channels. However, you may want to leave at least one channel in any unused bank. Then, if someone selects an "unused" bank, that channel will assure them that the TV is functional. Note: Some channels from factory testing may be in the channel banks if you have not yet run Auto Program. ADDING / DELETING CHANNELS A previously prepared programming chart is helpful. The channels available in your cable/antenna will be entered in Channel Banks 1, 2, 3, and 4. Note: Channels previously "Blanked" will be cleared; channels "Added" that are not currently available, will be omitted. Select a channel bank with an installer remote - -press SOURCE/BANK (and repeat). CHANNEL BANK and BANK number will be displayed. CHANNEL BANK BANK 1 Channel bank number display Channel Bank Program package 1 Basic cable channels 2 Extended cable channels 3 Extended with premium channels 4 Other cable installer options (Grouping is provided as an example only. ) 3. Use the ADD/DEL/BLNK item (also in the Setup menu) to customize your program package. You can also "Blank" a channel for accommodating an audio-only program source or in-house communication. Inactive TV Display (Channel Bank 4) The TV can be set up to be inactive; which would require an attendant using an installer remote to change to a "billable" active channel bank selection: Bank 1, 2, or 3. Note: For institution control of patient-accessible programming, channels in Bank 4 need to be removed. The BLNK (blank) channel function is "global" -- the same channel number is blanked in channel banks 1, 2, 3, and 4. INACTIVE TV PLEASE . CALL ATTENDANT 206-3684 PAGE 25 Managing the Channel Banks Examples of typical channel banks charts Figure 1. Typical channel banks after running Auto Program B Purpose A N K 1 2 3 4 Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A = Active - - Channel was found during AUTO PROGRAM Figure 2. Typical channel banks after running Auto Program, and customizing with Add/Del/Blnk B Purpose A N K 1 2 3 4 Basic Extend All CTV Other Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 BC A BC A BC A BC A A A A A A A A A A A A A A A A A D A A A D D D A D A A A D A A A D D D A D A A A D A A A D A A A D D A A D D D A D D A A D D A A A = Active D = Deleted BC = Blanked Channel Channel was found during AUTO PROGRAM Channel was deleted using Add/ Del option. Channel was blanked using BLANK channel option (ADD/DEL/BLNK). ADDING / DELETING CHANNELS It is best to do ADD / DEL customizing before doing "BLNK. " AUTO PROGRAM enters the same channels in Banks 1, 2, 3, and 4. AUTO PROGRAM removes any channels previously customized with ADD / DEL / BLNK. The channels available on your antenna / cable will be entered, and any channels previously entered but not currently available will be deleted. ADD and DEL (not BLNK) can be used independently for channel banks 1, 2, 3, and 4. Channel allocations in tuning bands: BROADCAST: 2 ­ 69 CABLE ­ CATV, HRC or ICC: 1 ­ 125 PAGE 26 206-3491-O Managing the Channel Banks PLAN YOUR CHANNEL BANKS BY FILLING IN THESE CHARTS (or use photocopies) B Purpose A N K 1 2 3 4 Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 B Purpose A N K 1 2 3 4 Channel Number 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 B Purpose A N K 1 2 3 4 Channel Number 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 B Purpose A N K 1 2 3 4 Channel Number 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 B Purpose Channel Number A 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 FM N K 1 2 3 4 206-3491-O PAGE 27 Installer Menus Use the Installer's Menus to make TV operation adjustments Accessing the Installer's Menu Installer's menus can be accessed by using the optional installer's remote control. Just press and hold MENU (about 8 seconds) until the display changes, then press 9, 8, 7, 6, then ENTER. [. . . ] Refers to the jack that receives a signal from a TV, VCR or other A/V device. Refers to the jack that sends a signal out of a VCR, DVD, or other A/V device. Picture and sound traveling through a cable, or over the air, to your television screen. Device that picks up the signal and turns them into picture and sound. [. . . ]